Geokon 8020-42 Скачать руководство пользователя страница 3

 

Warranty Statement 

 
Geokon, Inc. warrants its products to be free of defects in materials and workmanship, under 
normal use and service for a period of 13 months from date of purchase. If the unit should 
malfunction, it must be returned to the factory for evaluation, freight prepaid. Upon examination 
by Geokon, if the unit is found to be defective, it will be repaired or replaced at no charge. 
However, the WARRANTY is VOID if the unit shows evidence of having been tampered with 
or shows evidence of being damaged as a result of excessive corrosion or current, heat, moisture 
or vibration, improper specification, misapplication, misuse or other operating conditions outside 
of Geokon's control. Components which wear or which are damaged by misuse are not 
warranted. This includes fuses and batteries. 
 
Geokon manufactures scientific instruments whose misuse is potentially dangerous. The 
instruments are intended to be installed and used only by qualified personnel. There are no 
warranties except as stated herein. There are no other warranties, expressed or implied, including 
but not limited to the implied warranties of merchantability and of fitness for a particular 
purpose. Geokon, Inc. is not responsible for any damages or losses caused to other equipment, 
whether direct, indirect, incidental, special or consequential which the purchaser may experience 
as a result of the installation or use of the product. The buyer's sole remedy for any breach of this 
agreement by Geokon, Inc. or any breach of any warranty by Geokon, Inc. shall not exceed the 
purchase price paid by the purchaser to Geokon, Inc. for the unit or units, or equipment directly 
affected by such breach. Under no circumstances will Geokon reimburse the claimant for loss 
incurred in removing and/or reinstalling equipment. 
 
Every precaution for accuracy has been taken in the preparation of manuals and/or software, 
however, Geokon, Inc. neither assumes responsibility for any omissions or errors that may 
appear nor assumes liability for any damages or losses that result from the use of the products in 
accordance with the information contained in the manual or software. 
 
 

 

Содержание 8020-42














Отзывы: