manualshive.com logo in svg

Geokon 6300, Инструкция по эксплуатации

Поделиться
Скачать
Geokon 6300 Скачать руководство пользователя страница 16

10 

3.3 GK-403 Readout Box (Obsolete Model) 

 

The GK-403 can store gauge readings and apply calibration factors to convert readings to 

engineering units. The following instructions explain taking gauge measurements using Mode 

“B”. Consult the GK-403 Instruction Manual for additional information. 

 

3.3.1 Connecting Sensors  

 

Connecting sensors with 10-pin connectors: 

Align the grooves on the sensor connector (male), with the appropriate connector on the 

readout (female connector labeled senor or load cell). Push the connector into place, and 

then twist the outer ring of the male connector until it locks into place.  

 

Connecting Sensors with Bare Leads: 

Attach the GK-403-2 flying leads to the bare leads of a Geokon vibrating wire sensor by 

connecting each of the clips on the leads to the matching colors of the sensor conductors, 

with blue representing the shield (bare). 

 

3.3.2 Operating the GK-403 

 

1)

 

Turn the display selector to position “B”. 

 

2)

 

Turn the unit on.  

 

3)

 

The readout will display the vibrating wire output in digits. The last digit may change 

one or two digits while reading. 

 

4)

 

The thermistor reading will be displayed above the gauge reading in degrees 

centigrade. 

 

5)

 

Press the “Store” button to record the value displayed.  

 

If the no reading displays or the reading is unstable, see Section 5 for troubleshooting 

suggestions. The unit will turn off automatically after approximately two minutes to 

conserve power. 

 

3.4 Measuring Temperatures 

 

Each Vibrating tilt sensor is equipped with a thermistor for reading temperature. The thermistor 

gives a varying resistance output as the temperature changes. Geokon readout boxes will read the 

thermistor and display temperature in 

°

C automatically. To read the thermistor using an 

ohmmeter, complete the following: 

 

1)  Connect the ohmmeter to the two thermistor leads coming from the instrument. (Usually 

white and green.) Since the resistance changes with temperature are large, the effect of cable 

resistance is usually insignificant. 

 

2) 

Look up the temperature for the measured resistance in Table 2 in Appendix B.  

 

Содержание 6300

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды