Geokon 4500-9-HDF1 Скачать руководство пользователя страница 3

WARRANTY STATEMENT

GEOKON

 warrants its products to be free of defects in materials and workmanship, 

under normal use and service for a period of 13 months from date of purchase. If the 
unit should malfunction, it must be returned to the factory for evaluation, freight 
prepaid. Upon examination by 

GEOKON

, if the unit is found to be defective, it will be 

repaired or replaced at no charge. However, the 

WARRANTY IS VOID

 if the unit shows 

evidence of having been tampered with or shows evidence of being damaged as a 
result of excessive corrosion or current, heat, moisture or vibration, improper specifi-
cation, misapplication, misuse or other operating conditions outside of 

GEOKON

's 

control. Components that wear or are damaged by misuse are not warranted. This 
includes fuses and batteries.

GEOKON

 manufactures scientific instruments whose misuse is potentially dangerous. 

The instruments are intended to be installed and used only by qualified personnel. 
There are no warranties except as stated herein. There are no other warranties, 
expressed or implied, including but not limited to the implied warranties of merchant-
ability and of fitness for a particular purpose. 

GEOKON

 is not responsible for any 

damages or losses caused to other equipment, whether direct, indirect, incidental, 
special or consequential which the purchaser may experience as a result of the instal-
lation or use of the product. The buyer's sole remedy for any breach of this agreement 
by 

GEOKON

 or any breach of any warranty by 

GEOKON

 shall not exceed the purchase 

price paid by the purchaser to 

GEOKON

 for the unit or units, or equipment directly 

affected by such breach. Under no circumstances will 

GEOKON

 reimburse the 

claimant for loss incurred in removing and/or reinstalling equipment.

Every precaution for accuracy has been taken in the preparation of manuals and/or 
software, however, 

GEOKON

 neither assumes responsibility for any omissions or 

errors that may appear nor assumes liability for any damages or losses that result 
from the use of the products in accordance with the information contained in the 
manual or software.

No part of this instruction manual may be reproduced, by any means, without the written consent of GEOKON. The 
information contained herein is believed to be accurate and reliable. However, GEOKON assumes no responsibility 
for errors, omissions or misinterpretation. The information herein is subject to change without notification.

The GEOKON® wordmark and logo are registered trademarks with the United States Patent and Trademark Office.

Содержание 4500-9-HDF1

























Отзывы: