Geocoop RGT-03 Скачать руководство пользователя страница 3

RGT-03 GSM Thermostat 

 

 

 

3                                              ML_RGT03_V5_english.doc 

 

The wiring should be done in accordance with local regulations. The use of a maximum 10A fuse is 
highly recommended. 

Please note:  

The person who carries out the installation must have basic knowledge on electricity. 
Make sure the power is cut off before any operation! 

 

Initial setup 

First, prepare the SIM card by a GSM phone and insert into the SIM holder. (See previous picture!)  

SIM preparation: Insert the SIM card into a common GSM phone. In the menu, find and disable the 
security  function  that  makes  the  phone  asking  for  PIN  number  on  star  up.  Next,  type  the  phone 
number that belongs to the SIM card in the ’Own Number’ menu – or similar. (That is only to allow 
the  control  unit  to  acquire  the  time  from  the  GSM  network  during  turning  on.  However,  it  is  not 
essential to do, since it can be doing with SMS command later, when the control unit is turned on.) 
Now the card is ready to be inserted into the control  unit. 

 

Before  reinserting  the  cover,  the  initial  setup  is  to  be  done  to  adapt  the  RGT-03  to  the  actual 
application.  
Jumper JP3 and button S1, S2 and S3 will be used. 
 
1.

 

Turn power on and wait for displaying the 
time/date. 

2.

 

Make  JP3  shorted  by  the  supplied 
connector. 

3.

 

Scroll the menu up or down with button S1 
and S2 to check each parameter. Select the 
one you need to change by pressing button 
S3. A flashing value will then indicate that 
the value is ready to be changed. Now use 
button  S1  and  S2  to  alter  the  value.  Press 
S3 repeatedly to save the value and return 
to  the  menu.  The  chart  below  shows  the 
menu  points,  the  default  values,  and  the 
range of possible adjustment. 

 

Display 

Meaning 

Default 

Possible adjustment 

H/C Type 

type of heating/cooling system 

See separate table! 

P1  Tcorr 

temperature shift 

0°C 

-3 … + 3°C 

P2  Llim 

lower temperature limit 

5°C 

5 … 15°C 

P3  Ulim 

upper temperature limit 

40°C 

21 … 40°C 

P4  Pprot 

pump protection 

OFF 

OFF/ON 

P01 Time 

Sunday 1. switch time 

08:00 

00:00 – 23:59 

P01 Ref 

Sunday 1. temperature to switch to 

21°C 

lower temp. limit – 
upper temp. limit 

P02 Time 

Sunday 2. switch time 

12:00 

00:00 – 23:59 

P02 Ref 

Sunday 2. temperature to switch to 

21°C 

lower temp. limit – 
upper temp. limit 

P03 Time 

Sunday 3. switch time 

17:00 

00:00 – 23:59 

P03 Ref 

Sunday 3. temperature to switch to 

21°C 

lower temp. limit – 
upper temp. limit 

Содержание RGT-03









Отзывы: