GEO Calibration 1000 SP Скачать руководство пользователя страница 25

Страница: 25 / 26

Error codes

The following table describes the possible error codes displayed on the Error List of GEO 1000 SP

Error String

Control behavior

“No Analog Detected”

Control is turned off

Internal Hardware fault

“No Peltier”

Control is turned off

Internal over temp probe

fault fans will run

continuously.

“NO HumGen Temp”

Control is turned off

Internal temperature probe

failure.

“Peliter High Limit”

Control is turned off if halt on

errors is enabled

Internal cooling sensor is

above limit

“HumGen Low Limit”

Control is turned off if halt on

errors is enabled

Ambient temperature of

humidity generator is below

operating temperature

“HumGen High Limit”

Control is turned off if halt on

errors is enabled

Humidity generator is above

allowed limit. Check water

supply or ambient conditions

“EEPROM Cfg Reset”

Control not affected

Unit has reset its

configuration to factory

default review settings.

“EEPROM Cal Reset”

Control not affected

Factory calibration has been

reset to default. Please

contact GEO instruments.

Содержание 1000 SP



























Результаты поиска

Содержание 1000 SP

Отзывы:

Похожие инструкции для 1000 SP

Бренды по названию

Популярные бренды

GEO Calibration 1000 SP, Руководство по эксплуатации

Результаты поиска

Содержание 1000 SP

Отзывы:

Похожие инструкции для 1000 SP

Бренды по названию

Популярные бренды