background image

8

Subject to Technical Modifications of Combi 185 S/LS

Check and initial  

adjustment of the system

In order to achieve optimal operation of the system, an 

initial adjustment must be performed using professional 

equipment for measuring the atmosphere. 

The following items must be checked, although the system 

can be put into operation before the initial adjustment has 

been performed: 

1.  Check that the system has been correctly installed, and that 

all ducting has been insulated in accordance with directions.

2.  Check that various hatches can be opened so that it is  

possible to perform service and maintenance on the unit. 

3. 

Check that filters are clean (they can be dirty after 

 

installation), and replace as necessary before running initial 

adjustments. 

4.  Check that the condensation drainage is correctly installed 

with an appropriate water trap, and that this is protected 

against frost.

5.  Pour 1 l of water into the condensation tray, and check that  

it flows away without impediment via the condensation 

 

drainage hose. 

Default setting if the system is started up prior to initial 

adjustment:

Adjust all Supply air valves so that the valve which is  

closest to the unit is open at 3 turns from the closed  

position, while the one furthest away is open at 8 turns 

from the closed position.

The valves in between are to be open at 4-7 turns  

depending on how close they are to the unit. 

Optimal initial adjustment 

of the system

Professional equipment for measuring the atmosphere 

must be used. Check that all 5 items in the section above 

have been performed before the initial adjustment is con-

ducted. Subsequently, the system can be put into opera-

tion. 

The system should be adjusted initially for basic ventila-

tion which is speed 2. In order to reduce energy consump-

tion as much as possible, the overall atmospheric volume 

should first be adjusted to the desired level by changing 

the speed settings in the Service Menu. 

Then the initial adjustment is performed on the Supply air 

and exhaust valves using measuring equipment. (Remem-

ber to lock the valves when performing the initial adjust-

ment, and that the conducting plate on the Supply air 

valves is turned so that air is blown in the right direction) 

Finally, the overall atmospheric volume should be re-

checked and fine-tuned by adjusting the speeds for Step 

2in the Service Menu. Step 1 and Step 3 should then be 

adjusted to an appropriate interval in relation to Step 2.

Requirements for the hot  

water circuit

For the hot water installation, the following materials may 

be used: 

•  Copper

•  Stainless steel

•  Brass

•  Synthetic materials 

This is naturally dependent upon the materials which have 

already been used in the water circuit (of the dwelling). 

Incorrect combinations of materials may result in damage 

from corrosion. 

This requires special attention when galvanised 

components and components containing  

aluminium are used.

Using the water circuit

Fill the tank at the connector spigot and air out the tank 

by letting one of the uppermost hot water spigots remain 

open until no more air comes out.

Re-check the entire water circuit for any leaks. .

After start-up, it is necessary to check all connections for 

leaks. 

The cooling circuit

The unit has been delivered ready to run. No work needs 

to be performed on the cooling circuit. The control unit will 

automatically assume control of all functions and start up 

the compressor, ventilator fan, etc. in order to maintain the 

set water temperature.  

Содержание Combi 185 LS
















Отзывы: