background image

550-0636

Page 3

Gentex Super-Slide

®

 Mounting Bracket:

 

Allows the installer to pre-wire the system, test for 

system supervision, remove the signal head until 

occupancy, switch out Gentex signals without 

changing mounting brackets and has locking edge 

connector for snap-in-place installation.

Gentex Checkmate

®

 Instant Voltage Verification:  

It is often necessary to confirm the voltage drop 

along a line of devices. The access holes are 

provided in the back of the terminal block to 

allow the voltage to be measured directly without 

removing the device. Typically this would be done 

at the end of the line to confirm design criteria. 

Most measurements will be taken using the S+ and 

S- locations although access is provided to other 

locations. 

NOTICE

: CARE SHOULD BE TAKEN TO NOT SHORT 

THE TEST PROBES.

 FOR MODELS: GEC3-12 AND GES3-12 ONLY

To remove bezel, grip 

both sides of bezel 

and pull in a 

downward and 

outward motion.

Candela selection 

slider switch.  Depress 

center and slide switch to 

desired brightness level.

Break off pin and insert 

into hole at the bottom of 

the selector to lock candela 

setting.  Signal must be 

removed from bracket and 

pin pushed forward from 

backside out of hole to 

change candela.

SWITCH POSITION

TONE

3

4

5

Mechanical Temporal 3

ON

ON

ON

Mechanical - Continuous

OFF

ON

ON

2400Hz - Temporal 3

ON

OFF

ON

2400Hz - Continuous

OFF

OFF

ON

Chime - Temporal 3

ON

ON

OFF

Chime - Continuous

OFF

ON

OFF

Whoop

ON

OFF

OFF

Whoop

OFF

OFF

OFF

NOTICE

SWITCH POSITIONS 1 AND 2 IN THE OFF POSITION TO 

    SELECT ISOLATED HORN AND STROBE POWER INPUTS

w

  SWITCH POSITION 6 ON = HIGH DBA

w

  SWITCH POSITION 6 OFF = LOW DBA

THIS APPLIANCE WILL NOT OPERATE WITHOUT ELECTRICAL POWER.  AS FIRES FREQUENTLY CAUSE POWER INTERRUPTIONS, 

GENTEX SUGGESTS YOU DISCUSS FURTHER SAFEGUARDS WITH YOUR LOCAL FIRE PROTECTION SPECIALIST.

CAUTION: 

A jumper card is provided to test for 

correct wiring in the supervisory mode only.  

DO NOT pass alarm current through the jumper.

Содержание GEC3-12 Series

Страница 1: ...tic tab NOTICE WIRING SHOULD BE CONNECTED TO MOUNTING BRACKET PRIOR TO MOUNTING SIGNAL INCOMING POSITIVE POWER LEAD MUST BE BROKEN AND EACH LEAD IS TO BE INSERTED INTO EACH OF THE TOP TWO TERMINALS IF TWO POWER RUNS ARE MADE TO THE SIGNAL ONE FOR THE STROBE AND ONE FOR THE HORN ONLY ONE OF THE RUNS MUST HAVE ITS POSITIVE LEAD BROKEN AND PLACED UNDER THE TWO SEPARATE TOP TERMINALS A BARRIER IS PROV...

Страница 2: ...A 30 141 mA 224 mA 60 260 mA 459 mA 75 312 mA 460 mA Horn Decibel Levels Horn Current Ratings Over Input Voltage Range of 8 17 5V Horn Mode Minimum SPL at 10Ft Per ANSI UL 464 HIGH Minimum SPL at 10Ft Per ANSI UL 464 LOW Regulated 12VDC Max Operating Current mA HIGH Setting Regulated 12VFWR Max Operating Current mA HIGH Setting Temp 3 2400Hz 76 dBA 69 dBA 29 mA 48 mA Temp 3 Mechanical 75 dBA 68 dB...

Страница 3: ...zel and pull in a downward and outward motion Candela selection slider switch Depress center and slide switch to desired brightness level Break off pin and insert into hole at the bottom of the selector to lock candela setting Signal must be removed from bracket and pin pushed forward from backside out of hole to change candela SWITCH POSITION TONE 3 4 5 Mechanical Temporal 3 ON ON ON Mechanical C...

Страница 4: ...rom defects in workmanship and materials under normal use and service This warranty does not apply and is void if damage or failure is caused by accident abuse misuse abnormal use faulty installation liquid contact fire earthquake or other external cause operating the appliance outside Gentex s published guidelines or service alteration maintenance or repairs performed by anyone other than Gentex ...

Отзывы: