Genie Z-45/25 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 36

background image

Genie Z-45/25 DC & Genie Z-45/25J DC

Part No. 82595

Operator's Manual

Second Edition · First Printing

Copyright © 1999 by Genie Industries

First Edition:

Fifth Printing, April 2002

Second Edition: First Printing, June 2003

"Genie" and "Z" are registered trademarks of
Genie Industries in the U.S.A. and many other
countries.

These machines comply with
ANSI/SIA 92.5-1992.

Printed on recycled paper

Printed in U.S.A.

Important

Read, understand and obey these safety rules and
operating instructions before operating this machine.
Only trained and authorized personnel shall be
permitted to operate this machine. This manual should
be considered a permanent part of your machine and
should remain with the machine at all times. If you
have any questions, call Genie Industries.

Contents

Page

Safety ........................................................................ 1

Controls ..................................................................... 8

Pre-operation Inspection ........................................... 11

Maintenance ............................................................. 13

Function Tests .......................................................... 15

Workplace Inspection ................................................ 20

Operating Instructions ............................................... 21

Transport and Lifting Instructions .............................. 25

Decals ...................................................................... 28

Specifications ........................................................... 32

Contact us:

Internet: http://www.genielift.com
E-mail: [email protected]

«
1
2
3
4
...
»

Содержание Z-45/25





































Отзывы:

Нет отзывов

Похожие инструкции для Z-45/25

Бренд: Snorkel Страницы: 196

Бренд: Atlas Страницы: 82

Бренд: PALAZZANI Страницы: 191

Бренд: Manitou Страницы: 108

Бренд: Manitou Страницы: 138

Бренд: Manitou Страницы: 142

Бренд: Manitou Страницы: 160

Бренд: Mec Страницы: 56

Бренд: Mec Страницы: 260

Бренд: DINGLI Страницы: 73

Бренд: DINGLI Страницы: 48

Бренд: DINGLI Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды