manualshive.com logo in svg

Genie GTH-844, Руководство по обслуживанию и ремонту

Поделиться
Скачать
Genie GTH-844 Скачать руководство пользователя страница 69

April 2017

 

Service and Repair Manual

 

 

Manifolds

 

 

 

Part No. 1272854

 

GTH-844

 

57 

 

 

7-5 
Valve Adjustments - Secondary 
Function Manifold 

How t o Set t he Steer Syst em Pres sur e 

How to Set the Steer System 
Pressure 

Note: Be sure that the hydraulic oil level is visible in 
the inspection glass of the hydraulic tank. 

1 

Install a 0 to 1000 psi / 0 to 100 bar pressure 
gauge into test port 'TP' at the top of the 
secondary function manifold, refer to 
Secondary Function Manifold Components. 

2 

Start the engine. Allow the engine to idle after 
warming the engine to operating temperature. 

3 

Without operating any machine controls, 
observe the reading on the pressure gauge. 

 

Result: The pressure gauge reads 450 ±25 psi 
/ 31 ±1.7 bar. The pump is functioning 
correctly. 

 

Result: The pressure gauge fails to read 450 
±25 psi / 31 ±1.7 bar. The pressure setting 
needs to be adjusted. Refer to Repair 
Procedure, 

How to Adjust the Function Pump 

Pressure

. 

4 

Turn the machine off. Remove the pressure 
gauge from the test port. 

 

Bodily injury hazard. Spraying 
hydraulic oil can penetrate and 
burn skin. Loosen hydraulic 
connections very slowly to allow 
the oil pressure to dissipate 
gradually. Do not allow oil to 
squirt or spray. 

5 

Install a 0 to 3500 psi / 0 to 250 bar pressure 
gauge into test port 'TS' at the top of the 
secondary function manifold. Refer to  
Secondary Function Manifold Components. 

 

6 

Start the engine. Allow the engine to idle. 

7 

Fully turn and hold the steering wheel in the left 
direction and allow the wheels to fully turn to 
the left. Continue holding the steering while 
observing the pressure reading on the 
pressure gauge. 

 

Result: The pressure gauge reads 
2650 psi±50 psi  / 183±3.4 bar. The pressure 
setting is correct. Proceed to step 12. 

 

Result: The pressure gauge fails to read 
2650 psi±50 psi  / 183±3.4 bar. The pressure 
setting needs to be adjusted. Proceed to step 
8. 

8 

Turn the machine off. Hold the steer pressure 
reducing/relief valve with a wrench and 
remove the cap (schematic item PR3). 

9 

Adjust the internal hex socket. Turn it 
clockwise to increase the pressure or 
counterclockwise to decrease the pressure. 

 

Component damage hazard. Do 
not adjust the relief valve 
pressures higher than 
specifications. 

10  Install the relief valve cap. 

11  Repeat this procedure beginning with step 6. 

12  Turn the machine off. Remove the pressure 

gauge from the test port. 

 

Bodily injury hazard. Spraying 
hydraulic oil can penetrate and 
burn skin. Loosen hydraulic 
connections very slowly to allow 
the oil pressure to dissipate 
gradually. Do not allow oil to 
squirt or spray. 

 

Содержание GTH-844




























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды