manualshive.com logo in svg

Genie GTH-844, Руководство по обслуживанию и ремонту

Поделиться
Скачать
Genie GTH-844 Скачать руководство пользователя страница 27

April 2017

 

Service and Repair Manual

 

 

Specifications 

 

 

Part No. 1272854

 

GTH-844

 

15 

 

 

Torque Procedure 

Seal-Lok™ fittings 

1 

Replace the O-ring. The O-ring must be 
replaced anytime the seal has been broken. 
The O-ring cannot be re-used if the fitting or 
hose end has been tightened beyond finger 
tight. 

Note: The O-ring in Parker Seal Lok™ fittings and 
hose end are custom-size O-rings. They are not 
standard size O-rings. They are available in the 
O-ring field service kit (Genie part number 49612). 

2 

Lubricate the O-ring before installation. 

3 

Be sure the O-ring face seal is seated and 
retained properly. 

4 

Position the tube and nut squarely on the face 
seal end of the fitting, and tighten the nut finger 
tight. 

5 

Tighten the nut or fitting to the appropriate 
torque. Refer to the appropriate torque chart in 
this section. 

6 

Operate all machine functions and inspect the 
hose, fittings and related components to 
confirm there are no leaks. 

 

JIC 37° fittings 

1 

Align the tube flare (hex nut) against the nose 
of the fitting body (body hex fitting) and tighten 
the hex nut to the body hex fitting to hand tight, 
approximately 30 in-lbs / 3.4 Nm. 

2 

Using a permanent ink marker, make a 
reference mark on one the flats of the hex nut 
and continue the mark onto the body of the hex 
fitting. Refer to Illustration 1. 

 

Illustration 1 

1  hex nut 
2  reference mark 
3  body hex fitting 

 

Содержание GTH-844




























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды