Genie Magic XPS Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 29

background image

Page 23 of 29

TROUBLE SHOOTING GUIDE

1) INSUFFICIENT WATER TO THE BRUSHES

a) Make sure the solution flow control valve is open.

b) Confirm that there is water in the solution tank.

c) Make sure solution dispensing tubes are not clogged or obstructed.

2) THE MACHINE DOES NOT CLEAN SATISFACTORILY

a) Check the condition of the brushes or pads and replace them if necessary.

b) The brushes should be replaced when the bristles reach a length of 5/8 inches (15mm).

3) THE SQUEEGEE DOES NOT DRY THE FLOOR WELL

a) Check that the squeegee blades are clean.

b) Adjust the inclination of the squeegee.

c) Confirm the vacuum hose is correctly fitted into its port in the

recovery tank.

d) Remove the entire vacuum assembly and clean it.

Solution

Flow

Control

Lever

«
...
21
22
23
24
25
...
»

Содержание XPS






























Отзывы:

Нет отзывов

Похожие инструкции для XPS

Бренд: Canon Страницы: 28

Бренд: Windsor Страницы: 25

Admiral 10080010

Бренд: Windsor Страницы: 37

MEMORY CRAFT 4900 QC

Бренд: Janome Страницы: 182

Бренд: Singer Страницы: 51

Бренд: PowerBoss Страницы: 52

Бренд: Siruba Страницы: 2

Бренд: GBC Страницы: 38

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 32

Бренд: Black & Decker Страницы: 32

WRANGLER 2016 AE

Бренд: NSS Страницы: 20

Бренд: HQ Power Страницы: 20

Advance 9087381020

Бренд: Nilfisk-Advance Страницы: 99

Бренд: Horizon Fitness Страницы: 50

Бренд: Trelawny Страницы: 11

Бренд: Global Страницы: 46

Бренд: Global Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды