Genie Magic XPS Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 29

background image

Page 20 of 29

WEEKLY MACHINE MAINTENANCE

CLEANING THE SQUEEGEE HOSE

To obtain the best drying results, keep the

squeegee hose clean.

To clean the squeegee

hose it is necessary to:

1) Take off the vacuum hose from its vacuum

port on the squeegee.

2) Remove the other end of the vacuum hose

from the recovery tank.

3) Wash the inner part of the hose with clean

water.

4) Reassemble.

WARNING:

Do not wash the hose that

goes from the vacuum motor to the

vacuum cover.

SOLUTION TANK CLEANING

5) Remove the fill cap from the solution tank.

6) Rinse with clear water.

7) Remove the solution tank drain hose and cap

at rear of machine and empty the solution

tank.

WARNING:

Use gloves for protection from

contact with dangerous solution.

Do Not

Wash

Vacuum

Cover

Hose

Wash

Squeegee

Hose

Solution Tank

Fill Opening

«
...
18
19
20
21
22
...
»

Содержание XPS






























Отзывы:

Нет отзывов

Похожие инструкции для XPS

Бренд: Janome Страницы: 42

Бренд: Duerkopp Adler Страницы: 80

Бренд: Kärcher Страницы: 55

Бренд: Unicorn Страницы: 18

Бренд: Singer Страницы: 47

Бренд: Powermax Tech Страницы: 16

Бренд: MULTIQUIP Страницы: 74

Бренд: JUKI Страницы: 96

Бренд: COMAC Страницы: 29

Alto FLOORTEC 550 P

Бренд: Nilfisk-Advance Страницы: 60

Бренд: Nilfisk-Advance Страницы: 82

Advolution 2710

Бренд: Nilfisk-Advance Страницы: 60

Бренд: Canon Страницы: 2

Бренд: JUKI Страницы: 136

Genesis 1700 AC/DC

Бренд: Selco Страницы: 124

SR 9772 56109414

Бренд: Nilfisk-Advance Страницы: 40

Бренд: Toro Страницы: 35

Бренд: Tornado Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды