Genesys GEN10-240, Руководство пользователя

Страница: 38 / 80

30
16
Number Control/Indicator Description
Section
FINE button
18 ALARM indicator
Table 4-1: Front Panel controls and indicators
17
FINE indicator
AC Power switch 19
Voltage and Current Fine/Coarse adjustment control.
Operates as a toggle switch. In Fine mode, the
VOLTAGE and CURRENT encoders operate with high
resolution and in Coarse mode with lower resolution
(approx. 6 turns).
: Advanced Parallel Operation
Mode setting.
Auxiliary function
Green LED, lights when the unit is in Fine mode.
Red LED, blinks in case of fault detection. OVP, OTP
Foldback, Enable and AC fail detection will cause the
ALARM LED to blink.
AC On/Off control.
4.3 REAR PANEL
See Fig.4-2 to review the connections and controls located on the power supply rear panel.
Refer to Table 4-2 for explanations about the rear panel connections and controls.
Fig.4-2: Rear panel connections and controls
8~100V
Models
150-600V
Models (shown)
1
Number
Item Description Section
AC input
connector
2 DC output
Table 4-2: Rear panel connections and controls
3
Header with a screw plug connector (Phoenix Contact
PC6-16/4-GF-10,16)
3.7
Bus-bars for 8V to 100V models.
Wire clamp connector for 150V to 600V models (shown).
3.9.6
RJ-45 type connector, use for connecting power supplies to
RS232 or RS485 port of computer for remote control purposes.
When using several power supplies in a power system, the first
unit Remote-In is connected to the computer and the remaining
units are chained, Remote-In to Remote-Out.
Remote-In
connector
7.3
7.4
Green LED, lights when PREV button is pressed.
PREV indicator 15
10 8
9
1
5 7
3 4 6
2
5.15.2
J2
J1
ON
OFF
J3
SW1
J1
OUT IN
AC INPUT
29
Table 4-1: Front Panel controls and indicators
4.3 REAR PANEL
See Fig.4-2 to review the connections and controls located on the power supply rear panel.
Refer to Table 4-2 for explanations about the rear panel connections and controls.
Fig.4-2: Rear panel connections and controls
1
Number
Item Description Section
AC input
connector
2 DC output
Table 4-2: Rear panel connections and controls
3
Wire clamp connector for 1500W units.
IEC connector for 750W units.
3.7.1
3.7.2
Bus-bars for 6V to 60V models.
Wire clamp connector for 80V to 600V models.
3.9.6
RJ-45 type connector, use for connecting power supplies to
RS232 or RS485 port of computer for remote control purposes.
When using several power supplies in a power system, the first
unit Remote-In is connected to the computer and the remaining
units are chained, Remote-In to Remote-Out.
Remote-In
connector
7.3
7.4
J2
AC INPUT
ON
OFF
OUT IN
J3
J1
SW1
10
5 7
3
8 9
4
6
1 2
750W
1500W
6~60V
Models
80~600V
Models
16
Number Control/Indicator Description
Section
FINE button
18
ALARM indicator
17
FINE indicator
AC Power switch
19
Voltage and Current Fine/Coarse adjustment control.
Operates as a toggle switch. In Fine mode, the
VOLTAGE and CURRENT encoders operate with high
resolution and in Coarse mode with lower resolution
(approx. 6 turns).
: Advanced Parallel Operation
Mode setting.
Auxiliary function
Green LED, lights when the unit is in Fine mode.
Red LED, blinks in case of fault detection. OVP, OTP
Foldback, Enable and AC fail detection will cause the
ALARM LED to blink.
AC On/Off control.
Green LED, lights when PREV button is pressed.
PREV indicator 15
5.15.2
30