Genesis GTS10SB Скачать руководство пользователя страница 12

English

10" Table Saw   

 

  

Operator’s Manual                GTS10SB

12

 

ASSEMBLY AND ADJUSTMENT

 

WARNING: 

DO NOT connect to power source until assembly is 

complete. Failure to comply could result in accidental starting and serious 
personal injury.

 

WARNING:

 

If any part is missing or damaged, do not attempt to 

assembly the table saw, plug in the power source, or turn the switch on until the 
missing or damaged part is obtained and it installed properly. 

WORK STAND ASSEMBLY

Part Needed

9.   Short Top Brackets (A)   

10.  Long Top Brackets (B)   

11.  Short Support Bracket (C) 

12.  Long Support Bracket (D)  

13.  Stand Legs   

 

14.  Rubber Feet   

 

15.  Screws, Washers & Nuts   

32 sets

Use Screws, Washers and Nuts (15) to attach the stand 
pieces. Do not tighten the screws completely until leg 
stand is completely assembly. (See FIG. 3)
1. Attach the short top brackets 9 (A) to the stand legs 13. 
2. Attach the long top brackets 10 (B) to the stand legs 13
3. Attach  the short support brackets 11 (C) to the stand legs 13
4. Attach the long support brackets 12 (D) to the stand legs 13
5. Tap the four rubber feet 14 onto the bottom of the stand legs 13
6. Tighten all fasteners. 

 

 

WARNING: 

After completing adjustments, securely tighten all fasteners. 

An unstable stand may shift in use and cause serious personal injury.

MOUNTING THE TABLE SAW ON STAND

1.  Place the table saw on to the assembled stand so that the 

four mounting holes in the base of the saw are over the 
four mounting slots on the stand.

2.  Secure the table saw to the stand by using the four bolts, 

washers and nuts provided. (See FIG.4)

MOUNTING THE TABLE WITHOUT STAND

When  mounting  table  saw  to  a  work  bench  or  plywood, 
holes should be drilled through the supporting surface to the 
work bench or plywood and an opening must be made the 
same size as the opening in the bottom of the saw using the 
dimensions illustrated so the saw dust can drop through. 
1. Place  the  saw  on  the  mounting  surface,  and  mark  the 

location of the four 3/8” mounting holes. 

2. Remove the saw. Drill 3/8” holes in the mounting surface
3. Mark an 11” x11” square centered between four mounting 

holes. 

10

11

12

13

9

13

12

14

10

15

FIG 3

9

FIG 4

FIG 5

Содержание GTS10SB
























Отзывы: