background image

English

1/4 Sheet Palm Sander  

 

  

Operator’s Manual                GPS2303

Guidelines for Using Extension Cords

•  If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in 

Canada) to indicate that it is acceptable for outdoor use.

•  Be sure your extension cord is properly wired and in good electrical condition.  Always replace a 

damaged extension cord or have it repaired by a qualified person before using it.

•  Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

SPECIFIC SAFETY RULES FOR PALM SANDERS

 

 

WARNING:

 

 DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT 

(GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO 
PRODUCT SAFETY RULES. If you use this tool unsafely or incorrectly, you can 
suffer serious personal injury! 

•  Always hold the tool firmly in your hands before switching the tool 

“ON”. 

The reaction to the torque of the motor as it accelerates to full speed may cause the tool 

to twist.

• Do not leave the tool running.

 

Operate the tool only when hand-held.

• This tool has not been waterproofed, 

so do not use water on the workpiece 

surfaces.

• Ventilate your work area adequately 

when you perform sanding operations.

•  Wear eye and hearing protection. 

Always use safety glasses with side shields. 

Unless otherwise specified, everyday glasses provide only limited impact resistance, they are not 
safety glasses. Use only certified safety equipment; eye protection equipment should comply with 
ANSI z87.1 standards. Protective hearing equipment should comply with ANSI s3.19 standards.

•  Protect your lungs.

 

Wear a face or dust mask if the operation is dusty. Following this rule 

will reduce the risk of personal injury.

SAFETY RULES FOR PAINT REMOVAL

 

WARNING:

 

 

Extreme care should be taken when removing paint. The 

peelings, residue, and vapors of paint may contain lead, which is poisonous. 
Exposure to even low levels of lead can cause irreversible brain and nervous 
system damage. Young and unborn children are particularly vulnerable. 

Before beginning any paint removal process you should determine whether the paint you are removing 
contains lead. This can be done by your local health department or by a professional who uses a paint 
analyzer to check for lead.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate 

Amperes  

(At Full Load)

Extension Cord Length

25 Feet

50 Feet

75 Feet

100 Feet

150 Feet

200 Feet

0–2.0

18

18

18

18

16

16

2.1–3.4

18

18

18

16

14

14

3.5–5.0

18

18

16

14

12

12

5.1–7.0

18

16

14

12

12

10

7.1–12.0

18

14

12

10

8

8

12.1–16.0

14

12

10

10

8

6

16.1–20.0

12

10

8

8

6

6

Содержание GPS2303














Отзывы: