- Check that the two jumpers JP1 e JP2 [E] are set to position "A"
2) 2 buffer modules
8) 4 screws (M3x8)
5) 16 contacts x 7.5cm flat cable
11) Vocal Proc. Owner’s Manual
12) PS-GPS2500 Op. System Disk
10) Vocal Proc. Demo Disk
Video Cable NTSC (Din to Rca)
9) Video Cable PAL (Din to Scart)
6) 10 contacts x 40cm flat cable
7) 2 contacts x 10cm cable
Audio/Video board NTSC
4) 9 contacts x 15cm flat cable
1) Audio/Video board PAL
3) 34 contacts x 7.5cm flat cable
Part List:
(761152)
(120003)
(130428)
(955990)
(955994)
(271200)
(130317)
(761093)
(840204)
(841025)
(841049)
(841009)
(841004)
(761143)
10 contacts x 65cm flat cable
(841019)
and that the jumper J1 [F] is set to position "A".
position if the SIMM dram
modules are installed, on B
set on A position if the buffer
modules are intalled.
The jumper J1 [F] must be
NOTE:
KIT 970291 (PAL) - KIT 970292 (NTSC) - A/V Kit with Vocal Processor
- Locate the CPU Board [A] and insert the buffer modules [2] into the connectors [H].
- Fix the AUDIO/VIDEO Board [1] to the threaded locations of the support [B]
- Connect the cables [3-4-5-6-7] to the AUDIO/VIDEO Board [1]
by means of the screw [8].
and to the CPU [A] and amplifier [D] boards.
- Connect the cable [3] to the CPU board.
ENGLISH
Model
GPS2500 and PS2500
Instructions
Mounting
Mounting Instructions M-11
Leave the jumper J2 on
its position.
- Check that the two jumpers JP1 e JP2 [E] are set to position "A"
2) 2 buffer modules
8) 4 screws (M3x8)
5) 16 contacts x 7.5cm flat cable
11) Vocal Proc. Owner’s Manual
12) PS-GPS2500 Op. System Disk
10) Vocal Proc. Demo Disk
Video Cable NTSC (Din to Rca)
9) Video Cable PAL (Din to Scart)
6) 10 contacts x 40cm flat cable
7) 2 contacts x 10cm cable
Audio/Video board NTSC
4) 9 contacts x 15cm flat cable
1) Audio/Video board PAL
3) 34 contacts x 7.5cm flat cable
Part List:
(761152)
(120003)
(130428)
(955990)
(955994)
(271200)
(130317)
(761093)
(840204)
(841025)
(841049)
(841009)
(841004)
(761143)
10 contacts x 65cm flat cable
(841019)
and that the jumper J1 [F] is set to position "A".
position if the SIMM dram
modules are installed, on B
set on A position if the buffer
modules are intalled.
The jumper J1 [F] must be
NOTE:
KIT 970291 (PAL) - KIT 970292 (NTSC) - A/V Kit with Vocal Processor
- Locate the CPU Board [A] and insert the buffer modules [2] into the connectors [H].
- Fix the AUDIO/VIDEO Board [1] to the threaded locations of the support [B]
- Connect the cables [3-4-5-6-7] to the AUDIO/VIDEO Board [1]
by means of the screw [8].
and to the CPU [A] and amplifier [D] boards.
- Connect the cable [3] to the CPU board.
ENGLISH
Model
GPS2500 and PS2500
Instructions
Mounting
Mounting Instructions M-11
Leave the jumper J2 on
its position.
