General Monitors 580A Скачать руководство пользователя страница 37

Страница: 37 / 44

Model 580A

7.4 Cable Requirements

3-wire maximum cable length between controller and sensor assembly with one-way
resistance of 20 Ohms (total 40 Ohms loop):

AWG

METERS

FEET

20 580 1900
18

910

3000

16 1460 4800
14

2320

7600

Table 9: Maximum Cable Lengths

7.5 Sensors

The following is a list of GMI sensors available for use with the Model 580A Controller:

PART NUMBER

DESCRIPTION

10001-1

Standard Industrial Combustible Gas Sensor. Used for most
hydrocarbons and hydrogen. Temperature range –65°F to
+200°F (-55°C to +93°C).

10001-1R

Same as Part Number 10001-1, except greatly improved
resistance to poisons, such as HMDS
(Hexamethyldisiloxane) and H

S (Hydrogen Sulfide).

10014-1

High Temperature Standard Industrial Combustible Gas
Sensor. Same as Part Number 10001-1, except sensor body
is stainless steel.

10058-1

Same as Part Number 10001-1, except sensor body is
stainless steel.

10058-1R

Same as Part Number 10058-1, except greatly improved
resistance to poisons, such as HMDS
(Hexamethyldisiloxane) and H

S (Hydrogen Sulfide).

10022-1

Similar to Part Number 10001-1, except PTB approved.

10059-1

Same as Part Number 10022-1, except body is constructed
of stainless steel.

10015-1

High Temperature equivalent of Part Number 10022-1. It may
be used in temperatures up to 400°F (200°C).

Table 10: GMI Sensors Available for 580A System

NOTE:

Part Numbers 10001-1, 10058-1, 10022-1, and 10059-1 sensors are CSA C22.2

No. 152-1976 certified. Part Number 10252-1 sensor housing is normally used in
the Western Hemisphere. Special ATEX approved housings are normally used in
Europe.

Содержание 580A













































Результаты поиска

Содержание 580A

Отзывы:

Похожие инструкции для 580A

Бренды по названию

Популярные бренды

General Monitors 580A, Инструкция по эксплуатации

Результаты поиска

Содержание 580A

Отзывы:

Похожие инструкции для 580A

Бренды по названию

Популярные бренды