MOUNTING INSTRUCTIONS FOR MODELS with REEL
1. Select location within 2 feet of an electrical outlet. 1. Select location within 2 feet of an electrical outlet.
2. Take U shaped Bracket “A” and attach to solid 2. Screw the hanger Hook securely into the ceiling.
part of the wall or ceiling with screws provided. 3. Hang Reel on Hook.
3. Place Hanger Bracket “B” Inside U shaped 4. Close Hook with pliers to prevent Reel from
Bracket “A” lining up small holes in the Brackets. Coming off. Refer to point “A”.
4. Insert Locking Pin “C” through lined-up holes. Be 5. Adjust Cord Stop so light or outlet hangs at
sure to bend the end of locking pin as shown. Desired length when cord is retracted.
Care & Operation of your New
Stubby II LED Worklight
CAUTION
1.
Inspect cord regularly for damage and replace if necessary for user safety.
2.
Do not submerge in liquids.
3.
When hanging reel models on ceiling:
- By Hook: Close hook with pliers to prevent reel from coming down.
- By Bracket Pin: With reel in place, bend end of “L” shaped pin to
prevent pin from falling out.
- Read mounting instructions carefully before installing.
4.
Caution—Risk of Electrical Shock—Use in Dry Locations Only.
5.
Tool Tap Models:
- Do not exceed Tool Tap amperage rating of 12 amps (16 AWG).
- Pull cord all the way out of reel when using the tool tap.
OPERATION & MAINTENANCE
1.
Plug the unit into a 120 volt AC outlet. The power supply cord is UL listed and
meets OSHA standards for grounding of hand held tool.
2.
Disconnect the power supply before servicing the light.
3.
Keep the unit free from grease and dirt by using a damp cloth with mild deter-
gent, or waterless hand cleaners. This removes dirt from scratches in outer
tube and will provide the best output at all times. If tube is damaged or badly
scratched, it is easily replaced and is available as a replacement part.
4.
Do not use solvents such as gasoline to clean unit or cord as it makes the parts
brittle. Do not allow brake fluid to contact outer tube as it will cause permanent
damage.
Item Part No. Description
1
5000-0733 Bumper ring
2
5000-1371 Outer tube assy, Polycarbonate (includes items 1 & 5)
2
5000-1372 Outer tube assy, X-Treme Shield (includes items 1 & 5)
3
5000-0760 Twin spring steel hook w/tips
4
5000-1373 LED board w/end lite and heat sink
4
5000-1374 LED board less end lite with heat sink
5
5000-1375 Reflector, Polycarbonate
5
5000-1376 Reflector, X-Treme Shield
Item
Part No. Description
6
5000-0415
Handle 18/2 SVT cord (includes item 7)
6
5000-0416
Handle 18/2 SJTOW cord (includes item 7)
6
5000-0425
Handle 16/3 SJTOW cord (includes item 7)
7
5000-0213
Screw
8
5000-1187
Switch for LED board w/end lite (includes three of item 15)
8
5000-0477
Switch for LED board w/o end lite (includes two of item 15)
9
5000-0104
End cap, small black (18/2 SVT)
9
5000-0103
End cap, medium black (18/2 SJTOW)
9
5000-0741
End cap, large black (16/3 SJTOW)
10
5000-0479
Watertite clamp, large
11
5000-0480
Watertite clamp, small
12
5000-6300
Cord assembly, 1’ 16/3 SJTOW yellow
12
5000-6082
Cord assembly, 25’ 18/2 SJTOW yellow
12
5000-6084
Cord assembly, 25’ 16/3 SJTOW yellow
12
5000-6085
Cord assembly, 50’ 18/2 SJTOW yellow
12
5000-6087
Cord assembly, 50’ 16/3 SJTOW black
13
5000-6302
40’ 18/2 SJTOW Reel cord assembly, yellow (includes item 15)
13
5000-6281
40’ 16/3 SJTOW Reel cord assembly, yellow (includes item 15)
13
5000-6303
50’ 18/2 SVT Reel cord assembly, black (includes item 15)
14
5000-0775
Mounting hardware, 40 & 50’ reels
15
5000-0754
Closed end connector, insulated
16
5000-6304
40’ 18/2 SJTOW Reel assembly with mounting hardware
16
5000-6305
40’ 16/3 SJTOW Reel assembly with mounting hardware
16
5000-6160
50’ 18/2 SVT Reel assembly with mounting hardware
17
5000-1368
In-line Tool Tap assy
