background image

Owner’s Manual for Trimmer/Mower™

7

General Information and Setup

Attaching Cord Caddy

1.

See 

Figure 2-6

Attach top and bottom caddy

clamps (A) on handle bar.

Figure 2-6. Manual Caddy

2.

Secure manual caddy with #10 screw and #10
nylon locknut (B) and tighten

Adding Oil

IMPORTANT NOTE: The unit is shipped without oil in
the engine. Oil must be added prior to operation.

1.

Place unit on a firm, level surface, and verify
engine is cooled.

2.

See 

Figure 2-7

Remove oil dipstick/ fill cap (A)

and wipe dipstick clean.

Figure 2-7. Oil Fill and Dipstick Location

3.

Add 14 oz (414 mL) of engine oil. See 

Table 2:

Engine Oil Requirements

 to select the recom-

mended viscosity grade by temperature. SAE
15W-40 is recommended for general use.

Table 2 – Engine Oil Requirements

4.

Wait one minute for oil to settle.

5.

See 

Figure 2-8

. Reinsert dipstick into oil filling hole

without screwing it in and verify oil level is in the
crosshatched section (A).

Figure 2-8. Oil Range

6.

If oil level is low add a few ounces of oil at a time.
Check dipstick frequently to prevent overfill. Do not
overfill

7.

Install oil fill cap/dipstick and hand-tighten.

006813

A

B

B

A

(000135)

CAUTION

Engine damage. Verify proper type and quantity of 
engine oil prior to starting engine. Failure to do so 
could result in engine damage.

(000210)

WARNING

Skin irritation. Avoid prolonged or repeated contact with  
used motor oil. Used motor oil has been shown to cause  
skin cancer in laboratory animals. Thoroughly wash  
exposed areas with soap and water.

005958

A

SAE 30

5W-30

10W-30

006809

A

Содержание Trimmer/Mower

























Отзывы: