background image

8

Owner’s Manual for Trimmer/Mower™

General Information and Setup

Adding Fuel

NOTE: 

Never use contaminated gasoline or mixed gaso-

line with oil. don’t allow dust, foreign matter or water to
enter into the fuel tank.

1.

Place unit on a firm, level surface in a well venti-
lated area.

2.

Verify unit is OFF and cooled for a minimum of two
minutes,

3.

See 

Figure 2-9

. Clean area about fuel cap (A) and

remove cap slowly (A).

Figure 2-9. Fuel Cap Location

4.

Fill tank with fresh, unleaded gas (with a minimum
85 octane rating) to 0.25 in (6.4 mm) from the bot-
tom of the fill neck to allow for fuel expansion.

5.

Install fuel fill cap.

NOTE: 

Allow spilled fuel to evaporate before starting

unit.

High Altitude Replacement Kit

At high altitude, the standard carburetor air-fuel mixture 
will be too rich. Performance will decrease and fuel 
consumption will increase. A very rich mixture will also 
foul the spark plug and cause hard starting. Operation at 
an altitude that differs from that at which this engine was 
certified, for extended periods of time, may increase 
emissions. 

Proper operation at higher altitudes can be ensured by 
installing an altitude kit when required. See 

Table 3: 

High Altitude Replacement Kit

 to determine when an 

altitude kit is required. 

Table 3 – High Altitude Replacement Kit

Kits can be obtained by contacting Generac Customer
Service at 1-888-436-3722 (1-888-GENERAC), or

www.generac.com

. Kits must be installed by a qualified

individual. 

NOTE: 

If a carburetor is replaced,  the proper high altitude kit

jet will need to be installed into the replacement carburetor.

NOTE: 

The warranty may be void if necessary

installation of a high altitude kit is not made for high alti-
tude use.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are 
extremely flammable and explosive. Add fuel 
in a well ventilated area. Keep fire and spark 
away. Failure to do so will result in death 
or serious injury.

 

(000214)

DANGER

Explosion and Fire. Do not fill fuel tank past full line. 
Allow for fuel expansion. Overfilling may cause fuel 
to spill onto engine causing fire or explosion, which 
will result in death or serious injury.

WARNING

Explosion and Fire. Do not smoke while 
refueling unit. Failure to do so could result in 
death, serious injury, or property or equipment 
damage.

(000284a)

005958

A

Altitude Range

Part Number

0-3000 ft

Not required

3000-6000 ft

10000035131

6000-8000 ft

10000035106 

Содержание Trimmer/Mower

























Отзывы: