Generac Power Systems Trimmer/Mower Скачать руководство пользователя страница 10

Страница: 10 / 24

Owner’s Manual for Trimmer/Mower™

General Information and Setup

Remove Contents from Carton

See

Table 1.

Remove and verify carton contents prior

to assembly. Carton contents should contain the fol-

lowing:

Table 1 – Parts Supplied

Contact Generac Customer Service at 1-888-436-
3722 (1-888-GENERAC), or

www.generac.com-

with the unit model and serial number for any miss-
ing carton contents.

Record model, serial number, and date of pur-
chase on front cover of this manual.

Installing Wheels

See

Table 2-2

. Insert .510" X .875" X .1" washer

(A) onto axle.

Figure 2-2. Wheel Installed

Slide wheel onto axle with plastic hub facing out.

Install 7/16-20 locknut (B).

Repeat for the other wheel.

Adjusting Trimmer/Mower Handlebar

See

Figure 2-3

. Verify handlebar mounting bolts

(A) are tight.

Figure 2-3. Lower Handlebar Bolts

See

Figure 2-4

. Loosen adjustment knob (B) on both

sides and position handlebar at comfortable height.

Figure 2-4. Handlebar Adjustments

Tighten both adjustment knobs.

NOTE:

Verify adjuster teeth (C) mesh.

Installing Cutting Cords

NOTE:

Always install all four trimmer cords with cords of

equal length. Not installing all four cords or installing
cords of varying lengths will cause excessive vibration
and could damage the machine.

See

Figure 2-5

. Insert trimmer cord (A) into inlet

hole (B) and push it in until the end protrudes out
the other side (C) about 1/2 in (12.7 mm).

Figure 2-5. Installing Cutting Cords

Repeat until all four cords are installed.

NOTE:

The cord can only move through the cord head in

one direction. To remove an old cord the cord must be
pulled through the cord head.

Cutting Cord Tips

•

Do not store cords in sunlight. UV light causes pre-
mature wear.

•

Keep cords pliable by soaking them in room tem-
perature water for a few days before use.

•

Replace cords one at a time and use old cord to
mark the position for new cord being installed.

•

Remove any cord broken off flush at the line plate
with needle nose pliers.

•

Do not add additional cords to the head.

Adding addi-

tional cords creates drag and may cause wrapping.

Description

QTY

Nut, Nylon Lock, 7/16-20, LP

Cord Caddy

#10 Screw

#10 Nylon Locknut

005951

00952

005953

006358

Содержание Trimmer/Mower

























Результаты поиска

Содержание Trimmer/Mower

Отзывы:

Похожие инструкции для Trimmer/Mower

Бренды по названию

Популярные бренды

Generac Power Systems Trimmer/Mower, Руководство пользователя

Результаты поиска

Содержание Trimmer/Mower

Отзывы:

Похожие инструкции для Trimmer/Mower

Бренды по названию

Популярные бренды