manualshive.com logo in svg

Generac Power Systems Quietsource 005012-1, Руководство пользователя, Страница: 4 / 48

Поделиться
Скачать
Generac Power Systems Quietsource 005012-1 Скачать руководство пользователя страница 4

 2 

Study these SAFETY RULES carefully before installing, 
operating or servicing this equipment. Become familiar 
with this 

Owner’s Manual

 and with the unit. The gen-

erator can operate safely, efficiently and reliably only if 
it is properly installed, operated and maintained. Many 
accidents are caused by failing to follow simple and fun-
damental rules or precautions.

The manufacturer cannot anticipate every possible cir-
cumstance that might involve a hazard. The warnings in 
this manual, and on tags and decals affixed to the unit 
are, therefore, not all-inclusive. If using a procedure, 
work method or operating technique that the manufac-
turer does not specifically recommend, ensure that it 
is safe for others. Also make sure the procedure, work 
method or operating technique chosen does not render 
the generator unsafe.

DANGER

  Despite the safe design of this generator, 

operating this equipment imprudently, neglecting 
its maintenance or being careless can cause 
possible injury or death. Permit only responsible 
and capable persons to install, operate or maintain 
this equipment.

  Potentially lethal voltages are generated by these 

machines. Ensure all steps are taken to render the 
machine safe before attempting to work on the 
generator.

  Parts of the generator are rotating and/or hot dur-

ing operation. Exercise care near running genera-
tors. 

 GENERAL HAZARDS 

• For safety reasons, the manufacturer recommends 

that this equipment be installed, serviced and repaired 
by an Authorized Service Dealer or other competent, 
qualified electrician or installation technician who is 
familiar with applicable codes, standards and regula-
tions. The operator also must comply with all such 
codes, standards and regulations.

• Installation, operation, servicing and repair of this 

(and related) equipment must always comply with 
applicable codes, standards, laws and regulations. 
Adhere strictly to local, state and national electri-
cal and building codes. Comply with regulations 
the Occupational Safety and Health Administration 
(OSHA) has established. Also, ensure that the genera-
tor is installed, operated and serviced in accordance 
with the manufacturer’s instructions and recommen-
dations. Following installation, do nothing that might 
render the unit unsafe or in noncompliance with the 
aforementioned codes, standards, laws and regula-
tions.

•  The engine exhaust fumes contain carbon monoxide 

gas, which can be DEADLY. This dangerous gas, 
if breathed in sufficient concentrations, can cause 
unconsciousness or even death. For that reason, 
adequate ventilation must be provided. Exhaust 
gases must be piped safely away from any building 
or enclosure that houses the generator to an area 
where people, animals, etc., will not be harmed. This 
exhaust system must be installed properly, in strict 
compliance with applicable codes and standards.

•  Keep hands, feet, clothing, etc., away from drive belts, 

fans, and other moving or hot parts. Never remove 
any drive belt or fan guard while the unit is operat-
ing.

• Adequate, unobstructed flow of cooling and ventilat-

ing air is critical to prevent buildup of explosive gases 
and to ensure correct generator operation. Do not 
alter the installation or permit even partial blockage 
of ventilation provisions, as this can seriously affect 
safe operation of the generator.

•  Keep the area around the generator clean and unclut-

tered. Remove any materials that could become haz-
ardous.

•  When working on this equipment, remain alert at all 

times. Never work on the equipment when physically 
or mentally fatigued.

IMPORTANT SAFETY INSTRUCTIONS

40kW Liquid-cooled Generators

  SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe 

operation be copied and posted in potential hazard areas. Safety should be stressed to all 
operators, potential operators, and service and repair technicians for this equipment.

  SAVE THESE INSTRUCTIONS – This manual contains important instructions that should be 

followed during installation and maintenance of the generator and batteries.

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth 

defects or other reproductive harm.

WARNING:

This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:

Содержание Quietsource 005012-1

















































Отзывы:

Нет отзывов