Generac Power Systems Pro 6712, Руководство оператора

Страница: 12 / 72

Operation
10 Owner’s Manual for Power Washer
Apply Detergent
NOTE : DO NOT use caustic liquid with power
washer. Use ONLY power washer safe
detergents. Follow manufacturer instructions
on detergent label.
Apply detergent as follows:
1. Prepare detergent solution as required by
job.
2. Make sure siphoning tube remains fully
submerged into the detergent.
3. When inserting the siphon into a detergent
solution bottle, route the tube so as to
keep it from inadvertently contacting the
hot muffler.
4. Verify black detergent nozzle is installed.
NOTE : Detergent cannot be applied with high-
pressure nozzle (Yellow, White, Green or
Red). Only use black nozzle with detergent.
5. Start engine.
6. Firmly grasp spray gun with both hands
when using high-pressure spray to avoid
injury when spray gun kicks back.
7. Apply a high-pressure spray to a small
area and then inspect surface for damage.
If no damage is found, continue to apply
detergent.
8. Apply detergent to a dry surface, start at
lower portion of area to be washed and
work upward using long, even,
overlapping strokes.
IMPORTANT: Flush the detergent siphoning
system after each use. Contact an authorized
dealer or qualified service center with
questions.
Rinsing
1. Remove black detergent nozzle from
lance.
2. Select and install desired high-pressure
nozzle.
3. Point spray gun in safe direction and
squeeze trigger to flush remaining
detergent from system.
4. Keep spray gun a safe distance from area
you plan to spray.
5. Firmly grasp spray gun with both hands
when using high-pressure spray to avoid
injury when spray gun kicks back.
6. Apply a high-pressure spray to a small
area and then inspect surface for damage.
If no damage is found, continue rinsing.
7. Start at top of area to be rinsed, working
down with same overlapping strokes as
used for cleaning.
Clean Detergent Siphoning
Tube
Flush detergent siphoning tube after each
use, before stopping the engine.
1. Place detergent siphoning tube/filter in
bucket of clean water.
2. Remove high-pressure nozzle from nozzle
extension.
3. Select and install black detergent nozzle.
4. Flush for 1-2 minutes.
5. Shut engine OFF.
6. Point spray gun in a safe direction,
squeeze spray gun trigger to release
retained high water pressure. Engage
trigger lock.
After Each Use
DO NOT allow water to remain in unit for long
periods of time. Sediments or minerals can
deposit on pump parts and freeze pump.
Follow these procedures after every use:
1. Shut engine OFF.
2. Turn water supply OFF.
3. Point spray gun in a safe direction, and
squeeze trigger to relieve trapped
pressure.
4. Let engine cool.
5. Disconnect hoses from spray gun and
high-pressure outlet on pump. Drain water
from hoses, spray gun, and lance. Use a
rag to wipe off components.
6. Verify engine start switch and fuel valve is
OFF.
7. Pull recoil handle approximately six times
to remove remaining liquid from pump.
8. Store unit in a clean, dry area.
NOTE : If storing for more than 30 days, see
Storage section.
(000106b)
Fluid Injection. This machine produces
high-pressure fluid streams that can pierce
skin. Fluid injection could result in death or
serious injury.
WARNING
(000117c)
Personal injury. Risk of fluid injection.
Do not aim spray gun at people, animals,
electrical devices, or fragile items. Keep out
of reach of children. Failure to do so
could cause death or serious injury.
WARNING
(000112)
WARNING
Risk of Falling. Use of machine creates wet
areas and trip hazards. Be aware of work area
conditions. A fall could result in death
or serious injury.
(000114)
WARNING
Risk of Falling. Do not use this machine or
any components on elevated surfaces.
Doing so can result in a fall, serious injury,
or death.