manualshive.com logo in svg

Generac Power Systems MLT4150, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MLT4150 Скачать руководство пользователя страница 31

Owner’s Manual for Mobile Light Tower

27

Section 5: Troubleshooting

General Troubleshooting

Some  of  the  more  common  problems  are  listed  in  the
table below. This information is intended to be a check or
verification that simple causes can be located and fixed.
It does not cover all types of problems. Refer to the OEM
engine  operator’s  manual  for  additional  troubleshooting
information. Procedures that require in-depth knowledge
or skills should be referred to a GMASD.

If problems persist, contact Generac Mobile at 1-800-926-9768 for assistance.

(000139)

WARNING

Risk of burns. Allow engine to cool before 
draining oil or coolant. Failure to do so could 
result in death or serious injury.

General Troubleshooting Guide

Problem

Possible Cause

Solution

Low oil pressure 
shutdown

Low oil level

Verify oil level on dipstick. Add oil, if needed.

Oil leaking from engine

Visually inspect the engine for leaks.

Oil pressure switch failure

Refer to OEM engine operator’s manual to identify corrective action.

High coolant temperature 
shutdown

Low coolant level

Add coolant if needed. Allow engine to cool, then check coolant level in 
radiator. Restart engine and check coolant temperature. Stop engine 
immediately if coolant temperature is 210°F (99°C) or more.

Blockage in radiator

Inspect radiator shroud and ducting for blockage and remove any foreign 
matter.

Leakage in coolant hoses, 
engine block, or water pump

Inspect for visible leaks. Verify tension of water pump serpentine drive 
belt.
Remove load on generator and restart engine. Verify coolant temperature 
and shut engine down immediately if it starts to overheat. Refer to the 
OEM engine operator’s manual for additional information on engine 
overheating.

Unit cranks, but will not 
start

Fuel level low

Check fuel level in tank.
Verify fuel pump operation.

Restricted air filter

Inspect air filter for blockage.
Refer to OEM engine operator’s manual for additional information.

Содержание MLT4150













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды