manualshive.com logo in svg

Generac Power Systems MLT4060K, Руководство по эксплуатации

Поделиться
Скачать
Generac Power Systems MLT4060K Скачать руководство пользователя страница 35

Maintenance

32

MLT4060-80M/K Operating Manual

10454 O

Top-Wind Models

•

Apply a lightweight oil to the screw stem.

Figure 19 - Applying Oil to Jacks

TRAILER WHEEL BEARINGS

The trailer axles are

 

equipped with a grease zerk fitting to allow lubrication of the wheel bearings without the need 

to disassemble the axle hub. To lubricate the axle bearings, remove the small rubber plug on the grease cap, attach 
a standard grease gun fitting to the grease zerk fitting and pump grease into the fitting until new grease is visible 
around the nozzle of the grease gun. Use only a high quality grease made specifically for lubrication of wheel bearings. 
Wipe any excess grease from the hub with a clean cloth and replace the rubber plug when finished. The minimum 
recommended lubrication is every 12 months or 12,000 miles (19,312 km). More frequent lubrication may be required 
under extremely dusty or damp operating conditions.

Oil

Grease

Grease

Grease

Oil

Oil

Oil

Oil

00243

Discount-Equipment.com

Содержание MLT4060K















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды