Generac Power Systems MLT4060K Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 46

background image

Operation

10454 O

MLT4060-80M/K Operating Manual

21

VOLTAGE REGULATOR OPTION

The electronic voltage regulator controls the output of the generator by regulating the current into the exciter field.
The regulator has three screwdriver adjustable potentiometers that may be adjusted for voltage, stability and voltage
roll-off (U/F). The voltage regulator on your unit is adjusted before shipment from the factory. Contact Generac Mobile
Products for additional information before attempting to adjust the voltage regulator.

CUSTOMER CONVENIENCE RECEPTACLES

The control panel is equipped with multiple receptacles
for running accessories or tools from the generator.
Power is supplied to the receptacles any time the engine
is running and the main circuit breaker is switched to the
ON (I) position.

Note:

Do not pull more than 1000W from each receptacle

when the lights are on. This will overload the generator
and cause the main circuit breaker to trip. Should the
breaker trip, switch off the lights, remove some of the load
to the receptacles and wait 10 minutes for the bulbs to
cool before turning them back on.

Figure 12 - Receptacle Locations

With all of the lights off, the full generator output may be used with the optional 240V twist-lock receptacle.

SHUTTING DOWN THE UNIT

Prior to shutting down the unit, check with personnel using power supplied by the unit and let them know the power
is going to be turned off. Make sure the power shut down will not create any hazards by accidentally turning off
equipment that needs to be kept on (pumps, compressors, lights, etc.).

When you have finished using the unit, proceed with shut down as follows:

1. Remove any loads from the receptacles.

2. Switch the individual circuit breakers for each light and

each

receptacle to the OFF (O) position.

3. Switch the main circuit breaker to the OFF (O) position.

4. Turn the Control Power switch to the OFF (O) position.

Figure 13 - Circuit Breakers and Control Power Switch Positions

Note:

For extended storage time, disconnect the battery. For extended storage requirements, refer to the engine

operator’s manual.

120V

120V

240V

BREAKER

BREAKER

240V

BREAKER

NEUTRAL BONDED TO FRAME

I

O

120V GFCI

Receptacles

240V

Twist-lock

Receptacle

00114

I

O

I

O

I

O

I

O

CIRCUIT BREAKERS

GLOW

PLUG

OFF

RUN

START

CONTROL POWER SWITCH

00201

Discount-Equipment.com

«
...
23
24
25
26
27
...
»

Содержание MLT4060K















































Отзывы:

Нет отзывов

Похожие инструкции для MLT4060K

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: 3M Страницы: 2

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренд: Yanmar Страницы: 49

Бренд: Baltic Страницы: 68

Бренд: H&S Страницы: 76

Бренд: rbd instruments Страницы: 18

Бренд: Teac Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды