manualshive.com logo in svg

Generac Power Systems MAGNUM MTT15, Руководство по эксплуатации, Страница: 21 / 49

Поделиться
Скачать
Generac Power Systems MAGNUM MTT15 Скачать руководство пользователя страница 21

20

Inspect all electrical cords; repair or replace any that are cut, worn, or bare.

Ensure all winch cables are in good condition and centered on each pulley. Do not use if cables are 
kinked or beginning to unravel.

Check oil, coolant, and fuel levels. For more information, refer to 

“General Maintenance” on page 26

.

Ensure engine battery connections are secure.

Turn the battery disconnect switch on, if equipped.

Check the engine fan belt tension and condition.

Check the engine fan belt guard.

Check the engine exhaust system for loose or rusted components.

Ensure all covers are in place and secure.

Ensure the emergency stop switch is pulled out.

EMERGENCY STOP SWITCH

The unit is equipped with one emergency stop switch. For location of the emergency 
stop switch, refer to 

“Component Locations” on page 15

. The red button is clearly 

labeled “EMERGENCY STOP.” The switch can be accessed and activated with all 
doors closed and locked.

Activate the emergency stop switch by pushing th button in until it locks down. This 

will open the fuel circuit, shutting down the engine. The switch will remain locked until 
it is pulled out.

Use the emergency stop switch only when the unit must be shut down immediately. For any 

other shut down, refer to 

“Shutting Down the Unit” on page 22

.

STARTING THE UNIT

1.

Check that the main circuit breaker and individual 
circuit breakers for each of the lights are in the “OFF/
O” position. 

Note: When the red “TURN MAIN BREAKER OFF” light 
is illuminated, the main circuit breaker must be turned 
OFF (O). 

2.

Turn the key on the Control Power switch to the left 
“GLOW PLUG” position and hold the key in place for 
five seconds, or until the glow plug indicator turns 
red. As soon as it is glowing, turn the key to the right 
“START” position and hold it until the engine cranks and starts running. Release the key, it will move to the “RUN” 
position. 

Note: For cold weather conditions, refer to the engine operator’s manual for appropriate glow plug interval. 

Do not crank the engine longer than 10 seconds at a time. If the engine will not start, wait 

ST

OP

 E

M

E R

G E N

C

Y

00230

I

O

I

O

I

O

I

O

CIRCUIT BREAKERS

00202

GLOW

PLUG

OFF

RUN

START

RELEASE KEY

GLOW

PLUG

OFF

RUN

START

ACTIVATE GLOW PLUG

GLOW

PLUG

OFF

RUN

START

CRANK ENGINE TO START

00203

Discount-Equipment.com

Содержание MAGNUM MTT15


















































Отзывы:

Нет отзывов