Generac Power Systems MAGNUM MTT15 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 49

Generac Power Systems MAGNUM MTT15 Скачать руководство пользователя страница 10

9

SAFETY SYMBOL SUMMARY

This equipment has been supplied with numerous safety and operating decals. These decals provide important
operating instructions and warn of dangers and hazards. Replace any missing or hard-to-read decals and use care
when washing or cleaning the unit. Decal placement and part numbers can be found in the parts manual. Below is
a summary of the intended meanings for the symbols used on the decals.

Hot surface(s) nearby.

Dangerous voltage may be
present.

Belt/entanglement hazard; keep
body parts clear of this area.

Use clean diesel fuel only.

Crush hazard; keep body parts
clear of this area.

UV

Ultraviolet radiation hazard;
operate only with lens intact.

Burn/scald hazard;
pressurized steam.

Fire/explosion hazard; keep
open flames away from unit.

Unit electrical ground.

Asphyxiation hazard; operate
in well ventilated area.

Safety alert symbol; used to
alert you to potential personal
injury hazards.

Read and understand the
supplied operator’s manual
before operating unit.

Stop engine before fueling.

Fan hazard; keep body parts
clear of this area.

Do not step on this surface.

Do not stand on this surface.

Stay out of tank.

Stand clear while mast
is being operated.

Do not drink the water.

Do not lift.

00913

Contact with overhead electrical
power lines will cause serious
injuries or death.

Discount-Equipment.com

«
...
8
9
10
11
12
...
»

Содержание MAGNUM MTT15


















































Отзывы:

Нет отзывов