manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 37

Operation

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

33

NOTE: 

Disconnect the battery if the unit will be stored for

an  extended  period.  Refer  to  the  engine  operator’s
manual for additional extended storage procedures.

Automatic Shutdown

This  unit  is  equipped  with  a  low  oil  pressure  and  high
coolant  temperature  automatic  shutdown  system.  This
system automatically shuts off the fuel supply to stop the
engine  if  oil  pressure  drops  too  low,  or  the  engine
exceeds normal operating temperature. Return the main
circuit breaker to STOP to reset the unit after the cause
of shutdown has been determined.

Lowering the Mast—Manual 

Winch

1.

Shut  down  the  lights  and  engine.  See 

Shutting

Down the Unit

.

2.

Lower the mast.

3.

Use the winch handles to collapse the mast to its
lowest position. Verify the electrical cord does not
get  caught  in,  or  pinched  by,  the  mast  while  it  is
being lowered.

.

IMPORTANT  NOTE:  Contact  a  GMP  ASD  immedi-
ately if the mast hangs up or the winch cable devel-
ops slack.

4.

See

 

Figure 3-15

.  If  the  unit  is  going  to  be  moved,

rotate the mast so the lights face the rear of the unit.

Figure 3-15. Stowed (Travel) Position

 To rotate the mast:

a. Loosen the mast rotation knob.
b. Rotate  the  mast  until  the  white  arrows  are

aligned and the metal stop tabs are touching.

c. Tighten the mast rotation knob.

Lowering the Mast—Electric 

Winch (If Equipped)

NOTE: 

On  key  switch  models,  key  must  be  in  RUN  to

operate electric winch.

1.

Press  and  hold  the  upper  winch  control  switch
downward  to  collapse  the  mast  to  its  lowest
position.  Verify  the  electrical  cord  does  not  get
caught in, or pinched by, the mast while it is being
lowered.

2.

Shut  down  the  engine.  See 

Shutting Down the

Unit

.

3.

If the unit is going to be moved, rotate the mast so
the  lights  face  the  rear  of  the  unit.  To  rotate  the
mast:
a. Loosen the mast rotation knob.
b. Rotate  the  mast  until  the  white  arrows  are

aligned and the metal stop tabs are touching.

c. Tighten the mast rotation knob.

NOTE: 

The  electric  winch  models  are  equipped  with  a

safety limit switch. This switch disconnects power to the
winch after the mast is completely raised or lowered. This
prevents the cable from continuing to unwind and becom-
ing entangled around the winch drum.

IMPORTANT  NOTE:  Contact  a  GMP  ASD  immedi-
ately if the mast hangs up or the winch cable devel-
ops slack.

NOTE: 

If  the  light  tower  is  not  operational,  and  the

batteries do not have enough power to lower the mast, it
may  be  necessary  to  lower  the  mast  manually. Always
attempt  to  recharge  the  batteries  and  lower  the  mast
electrically before proceeding.

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

008646

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды