manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 30

Operation

26

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

6.

See Detail E. Rotate each jack handle clockwise to
start  leveling  the  trailer. Adjust  all  three  jacks  by
rotating their handles clockwise until they are firmly
in  contact  with  the  ground.  Continue  until  the
wheels  are  approximately  1  in  (2.5  cm)  off  the
ground (G).

7.

Before  raising  the  mast,  it  may  be  necessary  to
adjust the lamps. The lamps may be adjusted up,
down,  left,  or  right  by  aiming  them  in  the  desired
direction.

Raising the Mast—Manual Winch

1.

Set up and level the unit. See 

Light Tower Setup

.

2.

See 

Figure 3-2

.  Inspect  the  mast  cables  for

excessive  wear  or  damage.  Verify  the  cables  are
properly  centered  in  each  pulley  (A).  Inspect  the
electrical cord for damage.

3.

Rotate  the  mast  by  loosening  the  mast  rotation
knob (C) at the bottom of the mast. Turn the mast
until the lights face in the desired direction. Tighten

the  mast  rotation  knob  to  secure  the  mast  in
position.

4.

Using  both  hands,  rotate  the  winch  (B)  to  slowly
extend the mast. Verify the coiled electrical cord is
extending  at  the  top  sections  of  the  mast.  Stop
extending the mast when the colored mark (D) on
the second mast section is visible as seen in Detail
D.

Figure 3-2. Pulley Locations—Manual Winch

IMPORTANT  NOTE:  Contact  a  GMP  ASD  immedi-
ately if the mast hangs up or the winch cable devel-
ops slack.

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit 
before raising the mast. Keep the outriggers extended while 
the mast is up. Failure to do so could cause the unit to tip 
and fall and could result in death or serious injury. 

WARNING

Tipping hazard. Do not extend the mast beyond the 
colored mark on the second mast section. The unit 
can become unstable and tip or fall, causing injury.

(000262)

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

(000279)

Personal injury or equipment damage. Do not raise 
or lower the mast while the unit is operating. 
Doing so can break the lenses and cause the 
lamps to shatter.

WARNING

DETAIL D

STOP

008709

A

D

B

C

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды