Generac Power Systems Magnum MGG100M страница 48 Скачать руководство пользователя | Manualshive

Страница: 48 / 84

background image

Operation

40

MGG100M Operating Manual

36833 C

WARNING

Before any connections are made to the generator, make sure that the main circuit breaker

and the controller switch are in the OFF (O) position and that the negative (-) battery cable

is disconnected. Potentially lethal voltages may be present at the generator cam lock

receptacles.

WARNING

Never attempt to disable or modify the switch box door safety interlock. Equipment

damage, personal injury or death may result.

Figure 22 - Cam Locks

A ground connection is located on the far left of the cam lock set. The set

MUST

be connected to a good earthen

ground for proper operating safety. The generator neutral is bonded to ground when it is shipped from the factory.
The bonding plate will need to be removed when the generator is used as a standby power source. INSTALLATION
SHOULD BE IN COMPLIANCE WITH NATIONAL ELECTRIC CODE (NEC), AS WELL AS ANY STATE AND LOCAL
CODES OR REGULATIONS.

FRAME GROUND CONNECTION

Follow all NEC, state, and local regulations regarding frame ground connections.

Determine ground stud location and connect the ground wire to the ground connection lug, located inside the customer
disconnect switch box. This ground is the local reference ground to ground the unit frame only.

TRANSFER SWITCH

If the unit is connected to an emergency power system, a transfer switch must be used. A transfer switch must be
used in AUTO mode to deflect the load upon start-up.

00623

«
...
46
47
48
49
50
...
»

Содержание Magnum MGG100M





















































































Отзывы:

Нет отзывов

Похожие инструкции для Magnum MGG100M

Бренд: GCAN Страницы: 16

GD200-037G/045P-4

Бренд: INVT Страницы: 266

Бренд: CYP Страницы: 12

LS001-W100E2-AA-M4PK1

Бренд: Harbor Breeze Страницы: 2

Бренд: GME Страницы: 21

Бренд: Tvone Страницы: 13

Бренд: Pulsar Страницы: 4

Бренд: Humandata Страницы: 10

Бренд: Elation Страницы: 4

Бренд: Transition Networks Страницы: 5

Бренд: Caen ELS Страницы: 52

Бренд: AIMS Power Страницы: 10

Бренд: Moxa Technologies Страницы: 2

Бренд: Planet Страницы: 63

Бренд: Tektronix Страницы: 41

Бренд: Albatross Страницы: 65

Tsunami TSU-AT1000

Бренд: SoundTraxx Страницы: 6

Бренд: TSUNESS Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды