background image

Study these SAFETY RULES carefully before install-
ing, operating or servicing this equipment. Become 
familiar with this Owner’s Manual and with the unit. 
The generator can operate safely, efficiently and reli-
ably only if it is properly installed, operated and 
maintained. Many accidents are caused by failing to 
follow simple and fundamental rules or precautions.

The manufacturer cannot anticipate every possible 
circumstance that might involve a hazard. The warn-
ings in this manual, and on tags and decals affixed 
to the unit are, therefore, not all inclusive. If a pro-
cedure, work method or operating technique is used 
that the manufacturer does not specifically recom-
mend, ensure that it is safe for others. Also make 
sure the procedure, work method or operating tech-
nique utilized does not render the generator unsafe.

DANGER

  Despite the safe design of this generator, 

operating this equipment imprudently, neglect-
ing its maintenance or being careless can cause 
possible injury or death. Permit only responsible 
and capable persons to install, operate or main-
tain this equipment.

  Potentially lethal voltages are generated by 

these machines. Ensure all steps are taken to 
render the machine safe before attempting to 
work on the generator.

  Parts of the generator are rotating and/or hot 

during operation. Exercise care near running 
generators. 

 GENERAL HAZARDS 

• For safety reasons, the manufacturer recommends 

that this equipment be installed, serviced and 
repaired by an Authorized Service Dealer or other 
competent, qualified electrician or installation tech-
nician who is familiar with applicable codes, stan-
dards and regulations. The operator also must 
comply with all such codes, standards and regula-
tions.

•  Installation, operation, servicing and repair of this 

(and related) equipment must always comply with 
applicable codes, standards, laws and regulations. 
Adhere strictly to local, state and national electri-
cal and building codes. Comply with regulations 
the Occupational Safety and Health Administration 
(OSHA) has established. Also, ensure that the 
generator is installed, operated and serviced in 
accordance with the manufacturer’s instructions 
and recommendations. Following installation, do 
nothing that might render the unit unsafe or in 
noncompliance with the aforementioned codes, 
standards, laws and regulations.

•  The engine exhaust fumes contain carbon monox-

ide gas, which can be DEADLY. This dangerous gas, 
if breathed in sufficient concentrations, can cause 
unconsciousness or even death. For that reason, 
adequate ventilation must be provided. Exhaust 
gases must be piped safely away from any building 
or enclosure that houses the generator to an area 
where people, animals, etc., will not be harmed. 
This exhaust system must be installed properly, in 
strict compliance with applicable codes and stan-
dards.

• Keep hands, feet, clothing, etc., away from drive 

belts, fans, and other moving or hot parts. Never 
remove any drive belt or fan guard while the unit 
is operating.

•  Adequate, unobstructed flow of cooling and venti-

lating air is critical in any room or building hous-
ing the generator to prevent buildup of explosive 
gases and to ensure correct generator operation. 
Do not alter the installation or permit even partial 
blockage of ventilation provisions, as this can seri-
ously affect safe operation of the generator.

• Keep the area around the generator clean and 

uncluttered. Remove any materials that could 
become hazardous.

• When working on this equipment, remain alert 

at all times. Never work on the equipment when 
physically or mentally fatigued.

• Inspect the generator regularly, and promptly 

repair or replace all worn, damaged or defective 
parts using only factory-approved parts.

  SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe 

operation be copied and posted in potential hazard areas. Safety should be stressed to all 
operators, potential operators, and service and repair technicians for this equipment.

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth 

defects or other reproductive harm.

WARNING:

This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:

1-1

Standby Generator Sets

Important Safety Instructions

Safety 001  Re

v. 0  08/05

Содержание Guardian 005336-0

































































Отзывы: