manualshive.com logo in svg

Generac Power Systems 1067-0, Руководство пользователя, Страница: 13 / 20

Поделиться
Скачать
Generac Power Systems 1067-0 Скачать руководство пользователя страница 13

• Use the wire included in the kit (Figure 13) or a

small paper clip to free the foreign materials clog-

ging or restricting the nozzle.

Figure 13 — Removing and cleaning nozzle.

• Remove additional debris by back flushing water

supply through wand extension (Figure 14). Back

flush between 30 to 60 seconds. Turn wand exten-

sion to stream spray and move nozzle from low to

high while flushing.

Figure 14 — Backflushing the nozzle.

• Reinstall nozzle into the wand extension. DO NOT

over tighten.

• Reconnect the wand extension to the gun.
• Reconnect the water supply, turn on the water, and

start the engine.

• Test the pressure washer by operating with nozzle

in the high and in the low position.

ENGINE MAINTENANCE

See the engine owner’s manual for instructions on

how to properly maintain the engine.

SERVICE AND 
ADJUSTMENTS

See the engine Owner’s Manual for instructions on

how to properly service and adjust the engine

PREPARING THE UNIT FOR
STORAGE

Water should not remain in the unit for long periods of

time.  Sediments of minerals can deposit on pump

parts and “freeze” pump action.  If you do not plan to

use the pressure washer for more than 30 days,

follow this procedure:
1.Shut off the engine and let it cool, then remove all

hoses.

2.Place throttle lever in STOP position.

CAUTION:  Be sure lever is in “STOP”

position before you continue.  If you start

engine without proper water supply con-

nected, you can damage pump.

3.Empty the pump of all pumped liquids by pulling

recoil handle about 6 times.  This should remove

most of the liquid in the pump.

NOTE:

To protect unit from freezing temperatures,

draw windshield washer fluid into pump by pouring

windshield washer fluid into a 3-foot section of garden

hose connected to inlet adaptor and pulling recoil

handle twice.
4.Store in a clean, dry area.

STORING THE ENGINE

See the engine Owner’s manual for instructions on

how to properly store the engine.

13

H i g h   P r e s s u r e   W a s h e r

Generac 1500PSI  High Pressure Washer

GENER

A

C

Содержание 1067-0





















Отзывы:

Нет отзывов