Generac Power Systems 1042-2 Скачать руководство пользователя страница 17

Страница: 17 / 24

TROUBLESHOOTING POINTS

H i g h P r e s s u r e W a s h e r

GENER

Generac 2250PSI High Pressure Washer

PROBLEM

CAUSE CORRECTION

Engine will not start; or starts

1. Low oil level.

1. Fill crankcase to proper level.

and runs rough.

2. Dirty air cleaner.

2. Clean or replace air cleaner.

3. Out of gasoline.

3. Fill fuel tank.

4. Stale gasoline.

4. Drain gas tank; fill with fresh fuel.

5. Spark plug wire not connected

5. Connect wire to spark plug.

to spark plug.

6. Bad spark plug.

6. Replace spark plug.

7. Water in gasoline.

7. Drain gas tank; fill with fresh fuel.

8. Overchoking.

8. Open choke fully and crank

engine.

9. Excessively rich fuel mixture.

9. Contact Generac service facility.

10. Intake valve stuck open or closed.

10. Contact Generac service facility.

11. Engine has lost compression.

11. Contact Generac service facility.

Engine shuts down during operation.

1. Out of gasoline.

1. Fill fuel tank.

2. Low oil level.

2. Fill crankcase to proper level.

Engine lacks power.

Dirty air filter.

Replace air filter.

Engine hunts or falters.

Choke is opened too soon.

Move choke to halfway position
until engine runs smoothly.

All manuals and user guides at all-guides.com

Содержание 1042-2

























Результаты поиска

Содержание 1042-2

Отзывы:

Похожие инструкции для 1042-2

Бренды по названию

Популярные бренды

Generac Power Systems 1042-2, Руководство пользователя

Результаты поиска

Содержание 1042-2

Отзывы:

Похожие инструкции для 1042-2

Бренды по названию

Популярные бренды