background image


 

GENERAL DESCRIPTION 

The bi-amplified Smart IP Genelec 4430A install loudspeaker is a compact two-
way active loudspeaker for fixed installations. It requires only one CAT cable to 
connect, making installation easy. The 4430A loudspeaker is powered using the 
standard Power-over-Ethernet (PoE) technology, using PoE+ or PoE standards. 
The proprietary internal power supply in 4430A delivers an impressive short-term 
SPL.  

The 4430 is a high-resolution loudspeaker delivering a signal path and acoustic 
output that extends to ultrasonic frequencies. It uses Genelec’s Minimum 
Diffraction Enclosure (MDE) enclosure technology to reduce acoustic diffractions. 
Combined with the advanced Directivity Control Waveguide (DCW) surrounding 
the tweeter, this provides excellent frequency balance in difficult acoustic 
environments.  

The 4430A loudspeaker supports Genelec Smart IP technology. The Smart IP 
technology provides scalable power, audio and loudspeaker configuration, 
supervision and calibration features via a standard CAT cable, offering 
integrators unrivalled power, flexibility, cost-effectiveness and simplicity of 
installation.  

The 4430A has been designed for excellent sound quality and very long lifetime. 
The enclosure is made of environmentally friendly recycled die-cast aluminium. 
4430A is manufactured using certified sustainable methods. All essential parts of 
the loudspeaker can be recycled. 

The 4430A is available in black, white or 120 RAL colours on order. It is 
compatible with Genelec’s extensive range of mounting accessories for floor, 
ceiling, wall, or truss mounting. 

The 4430A loudspeaker contains  

  highly efficient dedicated Class D power amplifiers, one for each driver,  

  switched-mode power supply technology offering high SPL output using 

standard PoE+ and PoE power supply with an IP switch or power injector,  

  active crossover filter,  

  electronic system protection,  

  audio-over-IP streaming input,  

  balanced analogue line input,  

  flexible room acoustic compensation tool set built in.  

 

Содержание 4430A





















Отзывы: