CROSSOVER
CROSSOVER
CROSSOVER
CROSSOVER
CROSSOVER
SECTION
SECTION
SECTION
SECTION
SECTION
1034BC
1034BC
1034BC
1034BC
1034BC
SYSTEM
SYSTEM
SYSTEM
SYSTEM
SYSTEM
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
AMPLIFIER
AMPLIFIER
AMPLIFIER
AMPLIFIER
AMPLIFIER
SECTION
SECTION
SECTION
SECTION
SECTION
Lower cut-off frequency, -3 dB:
<32 Hz
Upper cut-off frequency, -3 dB:
>22 kHz
Free field frequency response
of system:
33 Hz - 20 kHz (±2.5 dB)
Maximum short term sine wave
acoustic output on axis
in half space, averaged from
100 Hz to 3 kHz:
@1m >123 dB SPL
Maximum long term RMS acoustic
output in same conditions with IEC-weighted
noise (limited by driver unit protection cir-
cuit):
@1m >118 dB SPL
Maximum peak acoustic output
per pair @ 2m from the engineer
with music material:
>125 dB SPL
Self generated noise level in
free field @ 1m on axis:
<15 dBA
Harmonic distortion at 100 dB SPL @ 1m on
axis / freq:
50...100 Hz
<1%
200...10kHz
<0.5%
Drivers:
Bass
2 x 305 mm (12") cone
Mid
130 mm (5") cone
Treble 25 mm
(1") metal dome
All drivers are magnetically shielded
Speaker weight:
84 kg (185 lbs)
Amplifier weight: 30 kg (66 lbs)
Speaker dimensions (horizontal mounting):
Height 489 mm (19
1
/
4
")
Width 1210 mm(47
5
/
8
")
Depth 412 mm (16
1
/
8
") *
Amplifier dimensions:
Height 310 mm (12
3
/
16
") [7U]
Width 483 mm (19")
Depth 250 mm (9
13
/
16
") *
* Without connecting cable. Cable connec-
tors require additional 100 mm (4") of space
behind the speaker and the amplifier.
Bass amplifier output power with an 8 Ohm
load:
Short term 2 x 400 W
Midrange amplifier output power with
an 8 Ohm load:
350 W
Treble amplifier output power with
an 8 Ohm load:
120 W
Long term output power is limited by driver
unit protection circuitry.
Slew rate :
80 V/µs
Amplifier system distortion at
nominal output:
THD
<0.05%
SMPTE-IM
<0.05%
CCIF-IM
<0.05%
DIM 100
<0.05%
Signal to Noise ratio, referred to full output:
Bass
>100 dB
Midrange
>100 dB
Treble
>100 dB
Mains voltage:
100/200V or 115/230V
Voltage operating range at
230V setting:
207 - 244V (-10/+6%)
115V setting:
104 - 122V (-10/+6%)
Power consumption:
Idle
70 W
Full output
1000 W
Input connector: XLR female
pin 1 gnd
pin 2 +
pin 3 -
Input impedance:
10 kOhm balanced
Input level for 100 dB SPL output @1m:
variable from +6 to -6 dBu
Input level for maximum short term output of
126 dB SPL @1m:
variable from +32 to +20 dBu
Subsonic filter below 27 Hz :
18 dB/octave
Ultrasonic filter above 22 kHz:
12 dB/octave
Crossover frequency:
Bass/Mid
400 Hz
Mid/Treble 3,2 kHz
Crossover acoustical slopes:
>24 dB/octave
Crossover level control operating range in 1
dB steps:
Bass
from 0 to -6 dB & MUTE
Mid
from 0 to -6 dB & MUTE
Treble from 0 to -6 dB & MUTE
Bass roll-off control in 2 dB steps:
from 0 to -8 dB
@ 32 Hz
Bass tilt control in 2 dB steps:
from 0 to -8 dB
@ 50 Hz
The calibration position is with all tone con-
trols set to 'off' and input sensitivity control
to maximum.
Genelec document BBA34BC001
COPYRIGHT GENELEC OY 4/1999
All data subject to change without prior notice
Genelec Oy, Olvitie 5
SF - 74100 IISALMI, FINLAND
Phone: +358 - 17 - 813 311
Fax:
+358 - 17 - 812 267
Email:
Web:
www.genelec.com
Genelec Inc, 7 Tech Circle
Natick, MA 01760, USA
Phone: +1 - 508/652-0900
Fax:
+1 - 508/652-0909
Email:
