1031A Operating Manual
Genelec Document D1031AR001 Copyright Genelec Oy 6.2003. All data subject to change without prior notice
www.genelec.com
AMPLIFIER SECTION
CROSSOVER SECTION
SYSTEM SPECIFICATIONS
Lower cut-off frequency, -3 dB:
<
47 Hz
Upper cut-off frequency, -3 dB:
>
22 kHz
Free field frequency response of system:
48 Hz - 22 kHz (± 2 dB)
Maximum short term sine wave acoustic output on
axis in half space, av er aged from 100 Hz to 3 kHz:
@ 1m
>
110 dB SPL
@ 0.5m
>
116 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by
driver unit pro tec tion cir cuit):
@ 1m
>
101 dB SPL
@ 0.5m
>
107 dB SPL
Maximum peak acoustic output per pair above
console top, @ 1 m from the engineer with music
ma te ri al:
>
120 dB
Self generated noise level in free field @ 1m
on axis:
<
10 dB (A-weighted)
Harmonic distortion at 90 dB SPL @ 1m on axis:
Freq:
50...100 Hz
< 3%
> 100 Hz
< 0.5%
Drivers:
Bass 210 mm (8") cone
Treble 19 mm (3/4") metal dome
Both drivers are magnetically shielded.
Weight:
12,7 kg (28 lb)
Dimensions:
Height
393 mm (15 1/2")
Width 250 mm ( 9 7/8")
Depth 290 mm (11 7/16")
Bass amplifier short term output power with a
8 Ohm load:
120 W
Treble amplifier short term output power with an
8 Ohm load:
120 W
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at nominal out put:
THD
< 0.05%
SMPTE-IM
< 0.05%
CCIF-IM
< 0.05%
DIM 100
< 0.05%
Signal to Noise ratio, referred to full out put:
Bass
> 100 dB
Treble
> 100 dB
Mains voltage:
230, 100/200 or 115/230V
according to region
Voltage operating range:
±10%
Power consumption: Idle
30 VA
Full output
160 VA
Input connector XLR female:
pin 1 gnd
pin 2 +
pin 3 -
Input impedance:
10 kOhm bal anced
Input level for 100 dB SPL output @ 1m:
variable from +6 to -6 dBu
Input level for maximum short term sine wave output
of 110 dB SPL @ 1m:
variable from +16 to +4 dBu
Subsonic filter below 45 Hz :
18 dB/octave
Ultrasonic filter above 25 kHz:
12 dB/octave
Crossover frequency, Bass/Treble:
2.2 kHz
Crossover acoustical slopes:
24 dB/octave
Treble tilt control operating range in 2 dB steps:
from +2 to -4 dB & MUTE
Bass roll-off control operating range in 2 dB steps:
from 0 to -8 dB @ 40 Hz
Bass tilt control operating range in 2 dB steps:
from 0 to -6 dB @ 80 Hz
& MUTE
The 'CAL' position is with all tone con trols set to 'off'
and the input sensitivity con trol to maximum (fully
clockwise).
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83881
Fax +358 17 812 267
Email [email protected]
In the U.S. please contact:
Genelec, Inc., 7 Tech Circle
Natick, MA 01760, USA
Phone +1 508 652 0900
Fax +1 508 652 0909
Email [email protected]
In China please contact:
Genelec China Representative Office
Soho New Town, 88 Jianguo Road
D-1504, Chaoyang District
Beijing 100022, China
Phone +86 10 8580 2180
Fax +86 10 8580 2181
Figure 4. The upper curve group shows the horizontal directivity
characteristics of the 1031A in vertical configuration measured at 1 m.
The lower curve is a 1/3 octave band power response, measured in an
IEC approved reverberation chamber.
Figure 5. The curves show the effect of the bass tilt, treble tilt and
bass roll-off controls on the free field response.
BASS TILT
TREBLE TILT
BASS ROLL-OFF
60
65
70
75
80
85
90
95
100
20
100
1k
10k
20k
105
110
AUDIO PRECISION 1031anec
vs
07 SEP 93 10:04:11
LEVEL(dBr)
FREQ(Hz)
90
95
100
15°
30°
AUDIO PRECISION 1031anec
vs
07 SEP 93 11:21:58
60
65
70
75
80
85
90
95
100
LEVEL(dBr)
20
100
1k
10k
20k
FREQ(Hz)
45°
0°
