Gemini XL-500 ll, Инструкция по эксплуатации

Страница: 5 / 9

PLACEMENT:
unit on a flat. Vibration free Use the tumtable feet to
stabiiize unit.
Try to unit as far from the speakers possible.
Keep unit away from exposure sun, heat, moisture or
dirt.
Keep the unit ventilated.
‘ONNECTIONS:
Plug the AC power plug into an appropriate outlet.
See Table A for proper connection of the output RCA plugs and ground
connector. Make
all the plugs are firmly plugged
appropriate To reduce hum, make the ground iug firmly
connected to ground
TABLE A
MIXER OR
RECEIVER
L
PHON0 L CHANNEL
R (RED) PHON0 R CHANNEL
GND (Spade Lug)
GND
BASIC OPERATION:
2.
3.
4.
5.
7.
3.
a record on RUBBER (3) PLATTER
Select desired by depressing the 33 or 45 SPEED
SELECTOR BUTTON (14).
Turn the POWER SWITCH (12) to “ON” position, at which the
strobe illuminator (built into the POWER SWITCH (12) and the
(for seiected will illuminate.
Remove the (if to your
Release the
ARM
(8) on ARM REST (9).
Push START STOP BUTTON (13). The tumtabie PLATTER (2) will
to
Push CUE LEVER (15) to the
Position tone arm over desired position on record and push
the CUE LEVER to the “DOWN” Position. The TONE
ARM (5) will
lower onto the record at which play will begin.
When play over, raise the TONE ARM move it ARM REST
(9). and secure it with the ARM (8).
10. You now have of tuming off power by tuming POWER
SWITCH (12) to the position, stopping the PLATTER (2) by
pushing the START STOP (13) and engaging
brake.
PLAY:
2.
Pushing CUE LEVER (15) to will the
TONE
ARM (5) to iift stopping play.
Pushing CUE LEVER (15) to the “DOWN” will the
TONE ARM (5)
to
siowiy lower onto the record at the where play
was interrupted.
PLAYING 45 RPM RECORDS:
1.
When playing a 45 rpm record with a large hole, first the
45 ADAPTOR (16) on the
2.
Be sure that the
45
SPEED SELECTOR BUTTON is pushed and
the 45 iliuminated.
2. not being used, the TARGET LIGHT should be off.
ADJUSTING THE PITCH CONTROL:
The XL-500 equipped with a PITCH CONTROL (20). When the
PITCH CONTROL (20) in the
position the will be 33 or
45 depending on SPEED SELECTOR BUTTON (14) pushed.
When the PITCH CONTROL is positioned off vary
depending on position of the PITCH CONTROL.
The PLATTER (2) with a STROBE RPM INDICATOR
STRIP (21) and the POWER SWITCH (12) contains built in STROBE
LIGHTS (22). When the PLATTER (2) is spinning, the STROBE
LIGHTS iliuminate the STROBE RPM INDICATOR STRIP. At
Hz the
bottom row of dots will appear to be stationary when of the
platter is 45 RPM and row from the
appear to be stationary at 33 RPM. At Hz, row from the
top represents 45 RPM and top row represents 33 RPM.
PITCH BEND:
1. Pushing the PITCH BEND BUTTONS (19) will temporarily raise or lower
without Releasing buttons will
retum to the siide
SECTION:
Type.. ....................................
Drive Manual Turntable
Drive Method ................................................................
Drive
Motor .....................................................................
DC Motor
Platter .......................................... Aluminum
13’ (332mm)
Dia.
Speed ............................................................................
or 45 RPM
S tarting Torque ...................................................................
1.2
Build-up
.....................
sec. standstill to 33
RPM
Braking System.. .................................................. Brake (Solenoid)
Wow and Flutter ..................................................................
WRMS’
l
This refers to the tumtable assembly and platter only and
of or
Rumble ....................................................................... Unweighted
TONEARM SECTION:
...............................................
Universal S-Shaped Tubular Arm
Length ........................................................ 1116” (230.1 mm)
Overhang ...................................................................... (15.2 mm)
..................................................... g Cartridge)
Offset Angle ...................................................................................... 22’
........................................ Less Than 7 m g (Lateral,
Tracking Error Angle. .. n at the groove and within
at the inner groove of a 30 cm (12”) record
Stylus Pressure Range .............................................. 0 5 g
Cartridge Weight Range 6 ............................................... 10 g
Headsheli Weight ...................................................................... 5.6 g
GENERAL:
Power
......................................................
Power Consumption .......................................................................
15 Watts
Dimensions ............................................................ 17 6”
x x 352mm
Weight ..................................................................... 22.5 10.2 Kg)
Specifications are without
dimensions shown are approximate.
LTGHT:
1. the TARGET
LIGHT SWITCH (17) and the
TARGET LIGHT
(18)
will
iliuminate
styius tip.
Page 4