Gemini XL-500 ll, Инструкция по эксплуатации

Страница: 4 / 9

purchasing a Gemini XL-500 tumtable. This of
art tumtable latest features. Prior to use, we suggest
all the instructions.
2
White . . . . . . . . . . . . . . . . . Left C h a n n e l
Blue . . . . . . . . . . . . . .
C h a n n e l
Red . . . . . . . . . . . . . . . . . . . . Right Channel
G r e e n R i g h t C h a n n e l
Mount the cartridge in the HEADSHELL (4) and tighten it
screws with
l
l
for quick
. Strobe illuminator
l
STANTON 680 CARTRIDGE USERS
When using a Stanton 680 or similar cartridge, where the body
grounded to a cartridge terminal, remove the grounding strap
from the cartridge body the cartridge ground terminal. Failure
to do this may
in hum.
1. Read all using equipment.
2. To reduce the risk of do not open the unit. There
NO USER PARTS INSIDE. Please conhct
Gemini Service Department or your authorized to speak to a
qualified technician.
HEADSHELL INSTALLATION:
Insert HEAOSHELL (4) into front of TONE ARM (5).
holding the HEAOSHELL (4) firmly in a horizontal Position, the
LOCKING NUT (6) HEADSHELL (4) in
the U.S.A., you have any this unit,
for customer Service. D
O
return
COUNTERWEICHT INSTALLATION: (SEE 3A 3B)
3. are set and sealed. Any attempt at
will void the warranty.
4. Be all AC power OFF while making connections.
5. Cables should be low shielded and of proper length. Make
sure that all and are tight and properly
6. Always begin with the audio controls set at
and the speaker volume set to OFF. Wait 8 to 10
to tuming up speaker volume prevent
that in darnage.
7. DO NOT EXPOSE TO RAIN OR MOISTURE.
1. Slide COUNTERWEIGHT (7) onto the rear of the TONE ARM (5)
with the numbered gauge forward.
2. Twist COUNTERWEIGHT lightly to it
onto rear of the TONE ARM (5).
ADJUSTING HORIZONTAL ZERO (0) BALANCE AND
1. Wlthout the remove (if your
cartridge has a detachable one).
2. Release ARM (8) and lift the TONE ARM (5) off ARM
REST (9).
8. DO NOT USE SPRAY ON ANY
CONTROLS OR SWITCHES.
3. advancement of the COUNTERWEIGHT (7) will
side of the TONE ARM (5) to be lowered.
will the opposite. the COUNTERWEIGHT (7) or
needed until the TONE ARM (5)
You easily by for the where the
TONE ARM (5) freely.
4. TONE ARM (5) on ARM REST (9) and it in with
ARM (8).
unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Dust
hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Tumtable platter
1
45 rpm adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rubber mat. . . . 1
Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Dust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Headshell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
5. TONE ARM (5) on ARM REST hold
COUNTERWEIGHT (7) steady with one hand while the
PRESSURE RING the numeral on the ring aligns
with the line on the TONE ARM (5) rear shaft. The horizontal
zero (0) should be completed.
6. Refioat the TONE ARM to ensure horizontal
(0)
has not been maintained, repeat counterweight 3 5.
7. After adjusting the horizontal (0) turn
COUNTERWEIGHT (7) the cartridge
recommend stylus pressure appears on PRESSURE
RING where it meets the line of TONE ARM (5) rear
shaft.
SEE FIG. 1 PAGE 1) FOR PART NUMBERS AND LOCATIONS.
ADJUSTING THE ANTI-SKATING CONTROL:
TURNTABLE PLATTER INSTALLATION:
Set the ANTISKATING CONTROL the as
pressure.
Set the TURNTABLE BASE (1) on a flat, surface. After to
ensure that all materials have been removed, gently the
PLATTER (2) on of the TURNTABLE BASE (1). Put
RUBBER MAT (3) on the PLATTER (2).
INSTALLING THE DUSTCOVER:
CARTRIDGE INSTALLATION: (SEE FIG. 2)
Because all have their own designs, please refer your
instructions to proper
Mount the onto
2. Hold in Position, directly above the tumtable, and slide the
hinge bases into the holders mounted on the rear
3. Always raise the before removal.
4. Avoid opening and closing the play. Undesirable
Vibration and skipping
Connect the lead to terminals. For your convenience,
the terminals of most are Connect lead
wire the terminal of the
Page 3