PAGE 08 - INSTALLER MANUAL
INSTALLER MANUAL - PAGE 09
7.0 - PROGRAMMING
The display will indicate:
FS: Factory Setting, standard adjustment , “Factory parameters”.
CS: Custom Setting, user-chosen adjustment, “Custom Parameters”.
Only expert users should modify these settings to avoid malfunctions of the parking
system.
!
To activate the programming procedure proceed as follows:
Press one of the two push-buttons on the control unit and keep it pressed for at least two seconds;
the system will activate and enter in the programming mode.
Press the two push-buttons on the control unit and keep them pressed for more than
two seconds to reset all the factory settings (FS).
!
Press the right push-button to go to the next
parameter.
Press the right push-button to increase the value
of the parameter.
When the parameter you want to modify is displayed, press one of the push-buttons and keep it
pressed until the display starts to blink; at this point you can modify the parameter.
Press one of the two
on the control unit and keep it pressed for at least two seconds
to register the value.
The display will stop blinking and the selected parameter will be displayed.
push-buttons
If no button is pressed within10 seconds, the system will exit the programming mode.
Press the left push-button to go to the previous
parameter.
Press the left push-button to decrease the value
of the parameter.
8.0 - SETTING OF PARAMETERS
Nr.
01
04
05
08
09
10
13
15
17
PARAMETERS
Volume of buzzer
Detection range of rear central sensors
Detection range of rear corner sensors
STOP zone of rear central sensors
STOP zone of rear corner sensors
Suppression of spare wheel indication
Delay of rear sensors activation
Service display (testing)
Sensitivity to detect obstacles
RANGE
0, 1, 2 (
)
From 120 to 180 cm (
)
From 50 to 95 cm
From 35 to 70 cm
From 35 to 70 cm
0, 1, 2, 3 (
)
0, 1 (
)
0, 2 (
)
1, 2, 3 (
)
Ref.1
Ref.2
Ref.3
Ref.4
Ref.5
Ref.6
SETTING
2
160
55
35
35
0
0
0
2
Ref.1
Ref.2
Ref.3
Ref.4
Ref.5
Ref.6:
: 0 = deactivated, 1 = low, 2 = high.
: the display having only 2 numbers, the range will be indicated as 20 and 80 instead of 120 and
180.
: 0= no activated.
1= minimum detection range from bumper, 10cm.
2= minimum detection range from bumper, 20cm.
3= minimum detection range from bumper, 30cm.
: if your vehicle has an automatic transmission, select “ 1”.
: 0 = not activated, 2 = distance from the closest rear obstacle.
1 low, 2 standard, 3 high.
9.0 - TESTING
!
!
!
!
!
!
!
!
Press one of the two push-buttons on the control unit (4) to enter in the programming mode.
Select parameter “15” (see “Setting of parameters”).
Press and keep pressed one of the two push-buttons and select the test (2 for testing the sensors).
Press and keep pressed one of the two push-buttons; the display will show “--”.
Proceed with the test of rear sensors; the sistem will indicate the value detected in real time.
Reprogram setting of parameter to “0”.
Press one of the two push-buttons and keep it pressed until the previously selected parameter is
displayed (15).
The system will automatically exit the programming mode 10 seconds after the push-button has
been pressed.
10.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) DIRECTIVE
The present device does not fall within the scope of Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE) as specified in art. 2.1 of L.D. no. 151 of 25/07/2005.
