Gemini CDX-1250 Скачать руководство пользователя страница 5

Страница: 5 / 19

CDX-1250

FUNCTIONS:

(CONTINUED)

SINGLE:

Pressing the

SINGLE

button engages

SINGLE

mode, in this

mode the

CDX-1250

will play one song and then stop. Pressing the

SINGLE

button again will then activate

CONTINUOUS

mode causing

the unit to play continuously (after the last track, the unit will return to
the first track of the disc and continue to play).

TIME

: The

TIME BUTTON

switches the time display between three

available sources, these three are

TIME ELAPSED

on the track,

TIME

REMAINING

on the disc and and

TIME REMAINING

on the track.

TIME ELAPSED

indicates how much time has currently gone by since the

play button was pressed,

TIME REMAING ON DISC

will count down the

time remaining on the entire disc and

TIME REMAINING ON TRACK

counts down the time that is left before the end of the track.

PITCH:

Pushing the

PITCH

button (the button will light up blue) activates

the

PITCH CONTROL SLIDE

. The pitch or speed of the

will change

plus or minus 12% depending on the position of the

PITCH CONTROL

SLIDER

. Push the

PITCH

button again to deactivate this mode.

PITCH CONTROL SLIDE

: Moving the

PITCH CONTROL SLIDE

up or down will lower or raise the pitch perc or - 12%.

PITCH BEND

: Pushing the

PITCH BEND BUTTONS

will automatically

raise the pitch up to +16% or lower the pitch down to -16% from the
existing pitch setting. Releasing the buttons will return the pitch
to the original pitch setting. You can use this function to match the beat
when mixing from one song to another

LOOP SECTION

: A

LOOP

repeats the section between the entry point

(

) and the exit point (

OUT

). To set a loop while the unit is playing,

start by pressing the

IN BUTTON

(it will light up) and when you reach

the desired end loop point press the

OUT BUTTON

(it will also light up).

The loop will continue playing until you press the

OUT BUTTON

again

allowing the music to continue from that point on, to re-engage the loop
you must press the

RELOOP BUTTON

. When you have released your

loop the

OUT BUTTON

will turn

OFF

and the

IN BUTTON

will remain lit

to indicate that your loop is stored in the

CDX-1250

memory. Pressing

the

IN BUTTON

again while the unit is playing will erase the previously

saved loop while saving your new loop entry point. Press

OUT

to exit

the loop and save a new complete loop. Press

RELOOP

to return to the

beginning of the previously saved loop from normal play. Press

RELOOP

repeatedly to cause the loop to stutter.

NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT,
WHILE ALL OTHERS WILL BE SEAMLESS.

PLAY/PAUSE

: Each press of the

PLAY/PAUSE BUTTON

causes the operation to change from

PLAY to PAUSE

or from

PAUSE

back to

PLAY

. The

PLAY/PAUSE BUTTON

remains lit when in

PLAY

mode, while it blinks in

PAUSE

mode.

CUE

: While the unit is playing and after the cue point has been

programmed, pressing

CUE

will cause the

player to enter the

PAUSE

mode (

PLAY

PAUSE BUTTON

blinks) at the programmed cue

point (the

CUE LED

is lit). Holding down the

CUE

button

changes the function to preview , and allows you to stutter start or play
from the programmed

CUE POINT

Releasing the

CUE

button will return

the

to the preset

CUE

point.

STOP BUTTON

: When pressed the

STOP BUTTON

stops the playback

of the

player.

TRACK SELECTION

: The

TRACK SELECTION

buttons let you select

the track to play.

+10

allows you to scan through the track selection

in increments of 10.

TRACK SKIP

allows you to scan through each

track one at a time.

NOTE : ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK
TO YOUR PROGRAMMED CUE POINT. YOU MUST BEGIN YOUR CUE SELECTION
OVER AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING OF THE NEWLEY
SELECTED TRACK.

AUX INPUT (MP3):

This 1/8” (3.5mm) input accepts any line level

source including MP3 players, Once a 1/8” (3.5mm) plug is inserted
the audio from the CD Player is cancelled out and only the

AUX

INPUT SOURCE

will be heard out of the main outputs.

MASTER OUTPUT ROTARY KNOB

: The

MASTER OUTPUT

rotary

knob adjusts the volume of the

MAIN MASTER

output.

TROUBLESHOOTING:

- If a disc will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.

- If the disc turns but there is no sound, check the cable connections,
if they are ok, check your amplifier or reciever.

-If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many cd’s are recorded out of spec and
will skip on most or all CD players. Before sending the unit for repair,
try playing a CD that you are sure plays properly.

SPECIFICATIONS:

GENERAL:

Type................................................................................Compact Disc Player
Disc Type...................................Standard Compact discs (12 cm & 8 cm)
Time Display.....................Track Elapsed, Track Remain, or Total remain
Variable Pitch.......................................± 12% Slider with Resume Switch
Pitch Bend............................................................................± 16% Maximum
Instant Start....................................................................Within 0.03 seconds
Installation...........................................................................................19" each
Dimensions.........Main unit: 19" x 3.5" x 10" (482.6 x 88.9 x 254 mm)
Weight Per Unit..................................................Main unit: 5.5 lbs. (2.5 kg)

AUDIO SECTION:

Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..............................................................................8 Times
Sampling Frequency.........................................................................44.1 kHz
Frequency Response............................................................20 Hz to 20 kHz
Total Harmonic Distortion...................................................Less Than 0.05%
Signal to Noise Ratio..............................................................................85 dB
Dynamic Range.......................................................................................85 dB
Channel Separation.................................................................85 dB (1 KHz)
Output Level...................................................................2.0 +/- 0.2V R.M.S.
Power Supply......................................................AC 115/230V, 60/50 Hz

SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITH-
OUT NOTICE FOR PURPOSE OF IMPROVEMENT.