background image

11.4.21 Function digital output 2

The output function can be set with the 

Function digital output 2

 parameter.

Index Sub-

In-

dex

Off-

set

Access

Rights

Length

Index name

Parameter

Type

Default

Values

0x4D

0

0

R/W

2 bits

Function digital

output 2

uint:8

2

0
1

2

3

Description of parameter values

Index name

Parameter

Values

Description

Function

digital output

0

(Output Open)

 Signal is output with the corresponding valve

position. Detection of Open depends on the setting of the

parameter 

Position Feedback

 (index 0x51 (see “Actuator po-

sition feedback“, page 45)) and a correct initialization.

1

(Output Close)

 Signal is output with the corresponding valve

position. Detection of Close depends on the setting of the

parameter 

Position Feedback

 (index 0x51 (see “Actuator po-

sition feedback“, page 45)) and a correct initialization.

2

(Output Error)

 Only output error detection.

3

(Output Error & Warning)

 Output error and warnings.

11.4.22 Logic digital inputs / outputs

The inputs and outputs can be inversed with the 

Logic digital inputs/outputs

 parameters.

Index Sub-

In-

dex

Off-

set

Access

Rights

Length

Index name

Parameter

Type

Default

Values

0x4E

1

0

R/W

1 bit

Logic digital

inputs / outputs

Input 1

Boolean

0

0

1

2

1

R/W

1 bit

Input 2

Boolean

0

0

1

3

2

R/W

1 bit

Input / output 1

Boolean

0

0

1

4

3

R/W

1 bit

Output 2

Boolean

0

0

1

Description of parameter values

Index name

Parameter

Values

Description

Logic digital inputs /

outputs

Input 1

0

(Active high)

 Input 1 

not

 inversed.

1

(Active low)

 Input 1 inversed.

Input 2

0

(Active high)

 Input 2 

not

 inversed.

1

(Active low)

 Input 2 inversed.

Input / output 1

0

(Active high)

 Input/output 

not

 inversed.

1

(Active low)

 Input/output inversed.

Output 2

0

(Active high)

 Output 

not

 inversed.

1

(Active low)

 Output inversed.

www.gemu-group.com

42 / 63

GEMÜ R639 eSyStep
Positioner (Code S0)

11 Specific data IO-Link (pin 6)

Содержание R639
































































Отзывы: