background image

10

Gerhard Geiger GmbH & Co. KG | 100W2507

0220

V001

en

EN

EN

12. Setting of the end stops

General information

In order to set the end positions of the 

GSI56.. E07 SMI

 motors, any setting switch – with 

continuous power supply – can be used that has a programming key or that allows a 

simultaneous UP/DOWN command. In this case, the UP/DOWN keys must be activated 

simultaneously instead of the programming key.

Article number / GEIGER setting switch
M56F152

with service terminal (D), 5 wires, SMI compatible

M56F153

with service terminal (CH), 5 wires, SMI compatible

 

I

Important: please observe the connecting diagram on the back of the 

setting switch.

Factory setting

•   The motor is set on the upper end position at the factory. The lower end stop is at the very 

other end. (at least lower end stop + 200 motor rotations). 

•   The motor command is in normal operation.

 

I

If the factory setting has been carried out and if the programming 

mode is activated, max. 100 revolutions can be done downwards. 

Reset to factory settings for a further run downwards.

13. Activate the programming mode 

 

I

Prerequisite: The motor is positioned between the upper and the 

lower end position. 

 

I

The GSI56.. E12 SMI can be set with any SMI setting switch that 

ensures a continuous power supply and has a programming key 

or that allows a simultaneous UP/DOWN command. If there is no 

programming key, the UP/DOWN keys must be simultaneously 

pressed.

Activate the programming mode  

via limit stop switch 

In order to activate the programming mode, the motor 

must be connected according to the diagram “push 

button operation” (see point 8).

Press the programming key of the limit stop switch or the 

UP/DOWN keys simultaneously until, after about 3 seconds, 

the motor confirms “end position programming activated” 

with 1 x click-clack. Then release the key. 

1 x

Press programming 

key for about 

3 seconds

Click-clack

PROG

PROG

Содержание INline GSI56 Series

















Отзывы: