background image

7

85198A_Manual of Electrical Installation for Pressure Probes KH-SIL2-Mobyle-series_07-2019_ENG

Failures and troubleshooting

In case of failures or malfunctions, on Table 2 you can find the most common failures and the means of appropriate 

search:

Table 2: troubleshooting

Failure

Possible causes 

Means of research

The sensor does not feel pressure

Obstruction of pressure 

channel

Fault on electronics output 

stage

1. Power down and remove the sensor

2. Verify eventual occlusion of the channel

     under pressure. Clean any residues and 

     material caps

The sensor is in alarm mode type  

“HIGH”

Bridge broken

Detachment of pins

Failure on primary element

1. Power down and remove the sensor

2. Check for overheating of electronics 

 housing. 

  Remove the causes of overheating, wait 

  until it cools down and power the sensor.

3. Powered the probe again, if the problem 

  persists, you should send back the probe to 

  Factory for repair. 

The sensor is in alarm mode type

“LOW” 

Power supply cable /connector

broken

Sensor not connected

Sensor not powered

Bridge broken

1. Power down and remove the sensor

2. Check that the power supply is connected.

  If necessary, restore the power supply.

3. Check for continuity between the pins of

  the connector and the power supply.

  If necessary, replace the cable and the    

 connector.

4. Check if the power values are within the

  specifications indicated in this manual. If

  necessary, replace the power supply.

5. If the problem persists, you should send

  back the probe to Factory for repair.

Applications to use the relevant category

The pressure sensors of KH Series may form part of a system for detecting the pressure that, when a threshold value is

exceeded, deactivates all the elements of pressure generation, through a control system.

The diagram “A” (Fig. 1) shows a possible application: the sensor detects the pressure and transduces it in an analog

electrical signal proportional to the value of the measured value; the SRP / CS compares the signal with the one set as

the alarm threshold: in case of exceeding the threshold it shall disable the elements of pressure generation.

VOLTAGE OUTPUT and  RATIOMETRIC

CURRENT OUTPUT

Fig. 1: application diagram A

Содержание KH-SIL2 Series









Отзывы: