gefran KFM LD Скачать руководство пользователя

Страница: 25 / 40

4.2. Replacing F2/1, F5, F9 with KFM LD

The attachment and mounting dimensions of the listed drives are identical. The assignments on the connection

plugs are identical. They can continue to be used on the KFM LD drive unchanged. Pin assignments with the

corresponding signals can be found in Chap. 4.3 on page 25.

Note !

With the KFM LD drive, it is possible that the connection lines may need to be lengthened on account of the prior separate ar-

rangement of the controller.

During installation, the drive must be de-energised!

Disassembly:

Disassembly of the F2/1, F9 and F9 drive is to be performed in the reverse order of that de-

scribed in Chap. 4.1 on page 23. To remove the cable from the controller housing, the connectors are to be

removed. Note the pin assignments and wire colours. After inserting the connection wires through the cable

bushings of the KFM LD drive, connect the connector according to your notes or connection diagram in Chap.

4.3 on page 25 and plug into the respective contact socket on the printed circuit board of the controller. With

the KFM LD drive, the connecting lines from the controller to the drive are no longer used. Furthermore, the

previous controller housing must be removed.

Installation:

The description in Chap. 4.1 on page 23 applies for the installation of the new KFM LD drive.

4.3. Connecting

4.3.1. X2 for trigger signals with pin assignments

Trigger signals

0V signals - active

+24V

Default TUL

Approval inspection

24V signals - active

+24V

Default TUL

Approval inspection

Tab. 19 Connect door drive via conventional 24V logic level Input

Acknowledge signals

24V/0V signals

Default TSU

Default TSO

Default > 150

N closing force

Default LT light

grid

Tab. 20 Connect door drive via conventional 24V logic level Output

0 Volt trigger and acknowledge signals active: left-hand graphic.
0 Volt trigger signals active. 24 Volt acknowledge signals active: right-hand graphic

Fig. 14

24 Volt control and acknowledge signals active:

Important

KFM LD • Instruction manual

Содержание KFM LD









































Результаты поиска

Содержание KFM LD

Отзывы:

Похожие инструкции для KFM LD

Бренды по названию

Популярные бренды

gefran KFM LD, Инструкция по эксплуатации

Результаты поиска

Содержание KFM LD

Отзывы:

Похожие инструкции для KFM LD

Бренды по названию

Популярные бренды