gefran KFM LD Скачать руководство пользователя | Manualshive

Страница: 23 / 40

background image

4. Installation

4.1. Car door drive

4.1.1. Installation of car door drive

Fig. 12

Item

Designation

Item

Designation

1

Transmission shaft

8

Insulating rubber

2

Insulating rubber

9

Tightening screw

3

V-groove belt

10

Header

4

Motor

11

Motor attachment screw

5

Inspection switch

12

Mounting elbow

6

Control device

13

Drive shaft

7

Motor console

14

Toothed belt for drive

Tab. 17

Installation sequence for mounting the drive:

Details on position numbers in brackets in the figure

1. Remove nut on insulating rubber (2) and mounting bolt (11) on mounting elbow (12).
2. Place V-groove belt (3) on serrated lock washer of the transmission shaft (1) and insulating rubber (2). Align

belts for installation with the motor drive shaft.

3.  Turn back tightening screw (9) on the motor console.
4.  Place motor with motor console (7) on mounting elbow (12) and insulating rubber (2).
5.  Place V-groove belt on drive and transmission shaft and tension by moving the motor.
6.  Loosely screw motor console to mounting elbow and insulating rubber.
7.  Tension V-groove belt by tightening the tightening screw. 1) Observe notices and remarks regarding belt

tension in Fig. 13!

8. Tighten mounting bolts and secure the adjustment of the tightening screw with the counter nut on the tight-

ening screw (Fig. 12).

9. Open and remove cover on controller housing with a Philips screwdriver.
10. Passing them through the cable bushing, connect the connections of the controller on the door drive motor

with the control system.

11. Connect motor and controllers according to instructions and the terminal connecting plan. See Chap. 4.2 on

Note !

After completing commissioning, the controller housing has to be closed with the cover. This is important for both versions

KFM LD • Instruction manual

23

«
...
21
22
23
24
25
...
»

Содержание KFM LD









































Отзывы:

Нет отзывов

Похожие инструкции для KFM LD

Бренд: Fastech Страницы: 40

Бренд: Teac Страницы: 19

Бренд: Saci Страницы: 40

DFPI-xxx-ND2P-E-NB3 Series

Бренд: Festo Страницы: 4

Masterflex L/S 07555-00

Бренд: Cole Parmer Страницы: 20

Бренд: Geckodrive Страницы: 9

Бренд: Becker Страницы: 28

ACTIVE CUBE Series

Бренд: BONFIGLIOLI Vectron Страницы: 200

CoolDrive Series

Бренд: Tsino Dynatron Страницы: 285

Бренд: Lenovo Страницы: 26

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 80

Бренд: Philips Страницы: 88

DVDirect VRD-MC3

Бренд: Sony Страницы: 88

Бренд: IACDRIVE Страницы: 272

Allen-Bradley PowerFlex 40 22B-B8P0N104

Бренд: Rockwell Automation Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды