www.gearscanada.com
TM
Gen
x
3
WARM TEK HEATED GLOVES
Measure (in inches) around
the widest part of
your hand (just below the
knuckles). Use
your dominant hand to check
your glove size.
IMPORTANT:
Gen X-3 Warm Tek Heated Gloves are designed to keep you warm when plugged into a 12-volt DC power source like what is typically found on most motorcycles, snowmobiles, ATV's, etc.
Simply connect and feel instant warmth.
HOOK UP OPTIONS
Option 1:
If you have a Gen X-3 heated jacket. No additional hook up's required. Plug in the COAX connector of the jacket into the
COAX connector of the glove.
Option 2:
Snap On/Off Glove Harness- 100226-1
(Comes in a pair – NOT INCLUDED)
Snap the Snap On/Off Glove Harness buttons to the back of your Gen X-3 vest and fix the other end (COAX Connector) to the glove.
Option 3:
Y GLOVE HARNESS – 100228-1 or 100273-1 (NOT INCLUDED)
Connect this Y harness to the battery cord (100227-1 not included) without the need of a Gen X-3 vest or the Gen X-3 Jacket. This will
help you run the gloves all by themselves. The Y glove harness can easily pass through your Jacket and then through the jacket sleeve.
The wire that comes out from the right sleeve of your arm is kept longer (Assuming the battery connection is done from the left side of
your Motorcycle). The switch cord should be fixed on the left side of the Motorcycle. That makes easy for the rider to get off the
Motorcycle.
CAUTION
Ensure that the wires do not get stretched or strained. Installation should be such that the wires do not get crushed when the seat is
closed. Make sure it is not in contact with any moving part. Make sure the connectors do not scratch your gas tank or any other part of the
vehicle. Do not route your battery cord next to power leads to avoid any sort of interference with your radio or intercoms.
IMPORTANT
If installing two battery cords, connect them in parallel. So both wires with the fuse are connected to +ve side of the battery and other two
are connected to –ve side of the battery.
CAUTION
Do not switch on the heated clothing if your vehicle engine is turned off. This may result in drainage of battery.
Do not leave any adapter cord plugged into the system when not in use.
Do not leave heated clothing plugged in and/or left on while not wearing them, fire may result.
Always disconnect the battery cord when leaving the vehicle and cover the COAX connector with the safety cap provided (to avoid
scratching, damaging the connections or body of the vehicle).
Do not use the Gen X-3 heated clothing on an infant.
Do not forget to disconnect your heated clothing, when leaving your vehicle.
Use a fuse rated for heated clothing combination selected.
CARE INSTRUCTIONS
Heated clothing is an electric device. Care should be taken in the storage and transportation of the heated clothing when not being worn.
With good care the heated clothing can last you many years. Never clip or sew any logo on the heated clothing as you run into the risk of
damaging a wire.
ATTENTION: READ BEFORE USING GLOVES
When removing gloves pull each finger individually, while being careful to hold outer glove and lining. Your weatherproof liner cannot be
sewn to outer glove as stitching holes will leak. If you remove your hand quickly, the liner may become inverted and will be difficult to
reposition.
Your gloves have a water proof liner, but your outer glove (textile or leather) will need to be treated with a waterproofing agent prior to
using in wet conditions. Failure to apply agent will result in a very wet and heavy glove that will take considerable time to dry.
PROBLEM SOLVING
If your heated apparel is not heating:
1. Check the fuse in the battery cord and replace if required
2. Check for loose connections (Battery cord terminals and all connectors)
3. If the heated clothing does not heat even after you changed the fuse, contact your local dealer with original receipt.
4. DO NOT attempt repair of the heated clothing on your own.
5. Modifying or tampering with their heating element can result in damage when used and will void the warranty.
!
!
!
!
!
!
!
WARNING :
Use next lowest rated fuse for the heated clothing combination selected depending on the current drawn by those heated gear.
3.1
1.7
2.9 / 3.7 / 5.9
HAND HEATER GRIP
(PAIR)
LEG CHAP
VEST
(SIZE DEPENDENT)
4.5
JACKET
GLOVES / LINERS
(PAIR)
2.2 / 1.7
PRODUCT
AMP DRAWN
FOOT WARMER
(PAIR)
1.2
EXAMPLE:
Gloves @2.2 amps + jacket @ 4.5 amps = 6.7 amps
Fuse required =10 amps
IMPORTANT:
WORKS IN PARALLEL WITH 12V DC POWER SUPPLY
(NOT COMPATIBLE WITH GEARS GEN X 2 HEATED CLOTHING)
GEARS TEMPERATURE CONTROLLER RECOMMENDED TO AVOID OVERHEATING
FOR BEST PERFORMANCE USE WITH GEARS HEATED CLOTHING AND GEARS WIRING HARNESS.
(Option 1 )
(Option 3 )
+
–
+
–
Sleeve
Connector
Switch/Temperature
Controller
(RECOMMENDED)
(Option 2 )
Snap
Connection
SNAP ON/OFF GLOVE HARNESS
100226-1
Important:
Y Glove Harness With
Single Controller ( Part # - 100273-1 )
recommended to avoid overheating
Y glove Harness
(100228-1 or 100273-1)
Battery cord (100227-1)
FEATURES:
!
Extremely comfortable glove made with soft drum-dyed leather
!
Designed with no feel heating elements MADE IN USA
!
Curved form fit heats the entire length of each finger, thumb and back of hand
!
Extra long gauntlet and Velcro closure keeps cold air out
!
Rain squeegee wiper provided on the thumb of the left glove
!
Wind proof and water proof breathable PORELLE insert keeps hand dry
!
A mid-loft, thermal insulation trapping more heat with smaller fibers, providing the same warmth
factor as higher-loft insulation, but without the added weight and bulk
!
Engineered to go with our Gen X-3 Warm Tek Heated Jacket or Gen X-3 Heated Vest
!
If you have a Gen X-3 Heated Jacket liner, no additional hook up's are required. Plug in your
heated gloves into the convenient hideaway plugs at the sleeves of Gen X-3 heated jacket
!
If you own a Gen X-3 Vest you will require additional hook up ( Part # 100226-1/ Snap On/Off
Glove Harness). Which can be easily connected to the snaps provided at the back of the vest
WARRANTY :
All warranties are for defective materials and workmanship
only for a period of one year. Original receipt is required
when you submit a claim to your dealer. This warranty shall
be void if the product failure is due to misuse, abuse, neglect,
accident, improper installation or any kind of tampering.
Normal wear and tear attributed to regular use is not a
warrantable defect.
If your harness came with a fuse installed you will need to take note what
rating it is. Review the chart and replace the installed fuse with the current
rating for your clothing combination. When you add or change the
combination of items, check the fuse requirement and change as needed.
Hand Size
(in inches)
7.0 – 7.5
7.6 – 8.0
8.6 – 9.0
9.1 – 9.5
9.6 – 10.0
10.1 – 10.5
Glove Size
XS
S
M
L
XL
2XL
SIZING:
!
If you have neither of the Gen X- 3 line of heated clothing you will require additional hook up's
{Part # 100228-1/Y Glove Harness (with switch) or 100273-1 /Y Glove Harness (with single controller) and 100227-1/Battery Cord}
!
Gen X-3 Warm Tek Heated gloves work in parallel (each glove uses 12 volts)
!
Glove ( as a pair) draws 2.2 amps of current to produce 27 watts of heat
!
Available Sizes : XS , S, M, L, XL, 2XL
