Gearmore T22B & T22H Скачать руководство пользователя

Страница: 16 / 20

By following a good maintenance program, your
equipment will last for many years.

1. Consult the operating and maintenance

instructions of the engine manufacturer for

engine care and maintenance.

2. Always check the oil level of the hydraulic

reservoir before operation. Operating the Log

Splitter without an adequate oil supply will

cause severe damage to the pump.

3. Change the oil filter after the first 25 hours of

operation. Thereafter, change the oil filter

every 100 hours or seasonally, whichever

comes first.

4. If the wedge becomes dull or nicked, a grinder

or sharpening tool can be used to sharpen it

while still attached to the cylinder. If it is

necessary to remove the wedge, the stripper

plate (71)* must be taken off by removing the

" bolts (68)*. Then remove the cylinder

support (66)* by taking out the

" bolts (63)*.

Then remove the

" x 3

" bolt (51)* that

connects the wedge to the cylinder. The

return hose (53)* may need to be disconnected

from the valve. Loosen hose clamp (18)* and

pull the hose off the fitting. Lift up the

cylinder carefully and slide the wedge out of

the channel.

5. Clean the breather cap after 25 hours of

operation. Clean it more often when operated

in dusty conditions. To clean, remove the

breather from the tank and flush with

kerosene or liquid detergent to remove the

dirt.

6. See also Repair and Maintenance Safety in

the Safety Information section of this manual.

7. All replacement parts must meet

manufacturer's specifications.

See

Parts Breakdown

(Pages 15 - 17)

in this manual.

5 MAINTENANCE

6 SPECIFICATIONS

Splitting Force:

22 Tons

Beam Size:

6" x 6"

Cylinder Size:

4" x 24"

Valve Type:

Auto-Return

Pump:

2-Stage, 11 GPM

Engine:

Honda 5.5 H.P. or

Briggs & Stratton 6 H.P.

Filter:

Replaceable

Hoses & Fittings:

Included

Tires:

4.80 x 8" Road Speed

Safety Chains:

Included

Ground Stand:

Included

Coupler:

2" Ball

Wedge Height:

Cycle Time:

•

13 Seconds

Max. Log Length:

26"

Total Reservoir Capacity:

17 Quarts

Height:

39" Horizontal

62" Vertical

Length:

Width:

44"

Built-In Log Cradle:

Yes

Shipping Weight:

T22H - 430 lbs.

T22B - 430 lbs.

•

Ideal case cycle times. Actual cycle times vary

depending on temperature, engine speed, pump

efficiency, altitude, etc.

Содержание T22B & T22H





















Результаты поиска

Содержание T22B & T22H

Отзывы:

Похожие инструкции для T22B & T22H

Бренды по названию

Популярные бренды

Gearmore T22B & T22H, Сборка и руководство по эксплуатации

Результаты поиска

Содержание T22B & T22H

Отзывы:

Похожие инструкции для T22B & T22H

Бренды по названию

Популярные бренды