GEA VARIVENT K Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 68

background image

•

If possible, take the valve out of the pipe section, with all housings and
housing connections

Notice

The permanent magnet on the switch bar is fragile.

Damage to the permanent magnet.
► Protect the permanent magnet against impact stress.

Warning!

Spring tension in the valve

Danger of injury when detaching the clamp connections (43, 46) as the
released spring pretension will suddenly lift the actuator.
► Before releasing the clamp joins, pretension the actuator using a manual
emergency actuator (H).

Carry out the following steps:

1.

Unscrew the control top (B).

2.

Pre-tension the actuator with an manual emergency actuator (H) (material no.
221.310.74) before unscrewing the valve disk.

3.

Remove the clamp connection (43) between housing and lantern.

4.

Vent the actuator.

5.

Withdraw the valve from the housing.

®

The valve insert has been removed.

10.5.2 Separating the Valve from the Actuator

Maintenance

Disassembling the Valve

430BAL008372EN_4

11.03.2022

41

«
...
39
40
41
42
43
...
»

Содержание VARIVENT K





































































Отзывы:

Нет отзывов

Похожие инструкции для VARIVENT K

Бренд: Watts Страницы: 2

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: C3 Custom Coolers Страницы: 16

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: Hanwell Страницы: 34

Бренд: HANSONG Страницы: 11

Бренд: Datapath Страницы: 12

Бренд: Hansen Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды