GEA VARIVENT K Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 68

background image

10

Maintenance

10.1

Safety instructions

Maintenance and repair

Before starting any maintenance and repair work on the electrical devices of the
valve, carry out the following steps in accordance with the "5 safety rules":

•

Isolate from the power supply

•

Take appropriate measures to prevent switch on

•

Test absence of voltage

•

Earthing and short-circuiting

•

Cover or safeguard any adjacent live parts.

For maintenance and repair, the following principles apply:

•

Observe the intervals specified in the maintenance schedule.

•

Only allow qualified staff to carry out maintenance or repair work on the valve.

•

Before starting any maintenance or repair work, the valve must be switched
off and secured against being switched back on. Work may only be started
once any residual energy has been discharged.

•

Block access for unauthorized persons. Put up notice signs which draw
attention to the maintenance or repair work going on.

•

Do not climb on the valve. Use suitable access aids and working platforms.

•

Wear suitable protective clothing.

•

Only use suitable and undamaged tools to carry out maintenance work.

•

When replacing parts only use approved, fully functional load lifting devices
and lifting accessories which are suitable for the intended purpose.

•

Before setting the magnetic separator back into operation, refit all safety
devices as originally provided in the factory. Then check that all safety
devices are working correctly.

•

Make sure lubricants are used properly.

•

Check pipes are firmly secured, also check for leaks and damage.

•

Check that all emergency stop devices are working correctly.

Disassembly

For disassembly, the following principles apply:

•

Only allow qualified staff to disassemble the valve.

•

Before starting disassembly, the valve must be switched off and secured
against being switched back on. Work may only be started once any residual
energy has been discharged.

•

Disconnect all power and utility lines.

•

Markings, e.g. on lines, must not be removed.

Maintenance

Safety instructions

430BAL008372EN_4

11.03.2022

37

«
...
35
36
37
38
39
...
»

Содержание VARIVENT K





































































Отзывы:

Нет отзывов

Похожие инструкции для VARIVENT K

Бренд: Ebyte Страницы: 34

Бренд: YASKAWA Страницы: 61

Бренд: Garmin Страницы: 4

Бренд: RADEMACHER Страницы: 48

Бренд: Xylem Страницы: 48

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: Dahua Страницы: 137

Diaval AF Series

Бренд: Comeval Страницы: 10

SMARTCONNECT SMART/REP

Бренд: Zeta Alarm Systems Страницы: 48

AMES Maxim Series

Бренд: Watts Страницы: 8

Бренд: fadini Страницы: 40

Бренд: Harsen Страницы: 55

Бренд: Wabtec Страницы: 5

Бренд: Madas Страницы: 48

Бренд: Proteco Страницы: 21

Бренд: ADDAC System Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды